TF360 and ShapeShifter and other questions

OSH · 05 March 2023, 20:42

Ok, I'm ran out ideas.
I have TF360, and I want to launch ShapeShifter. But I can't. Everything I see is a grey screen. Nothing is loaded. I'm using MuLib package and MuEVD - but it doesn't work. And in MULTISCAN Productivity mode is quite slow. And second question: why I can't use CD-ROM? When I insert CD into CD drive, it doesn't start to rotate. So I can't make fresh Install of OS 3.9 SE under Amiga, I have to do this under FS-UAE. Anyone here has TF360? Which 060.library will be the best for this card?

Akiko · 05 March 2023, 23:15

I have not tried ShapeShifter on my TF360 card yet, but perhaps it's the same issue that exists on the TF1260 and was resolved by a user on exxos?

https://exxosforum.co.uk/forum/viewt...7a51b289547c71

The TF360 does not support the CD32 CD-ROM drive, at least not on the latest firmware, the TF360 developer Stephen Leary mentioned on his Youtube channel that he is actively looking for a fix, so hopefully if it's resolvable it will appear with the next firmaware update.

OSH · 06 March 2023, 00:40

No. ehide.device doesn't help. I can't load it via Loadmodule, because I loaded scsi.device too. And without scsi.device, I can't boot system.

supaduper · 06 March 2023, 04:55

The CD does not work with the TF360 yet,did you not read the info that would have been provided to you when you purchased the board ? renember this is still in dev

OSH · 06 March 2023, 10:45

Quote:

Originally Posted by supaduper

The CD does not work with the TF360 yet,did you not read the info that would have been provided to you when you purchased the board ? renember this is still in dev

OK, but I asked about other things also. For example, why I can't launch ShapeShifter.

Seiya · 06 March 2023, 12:31

FS-UAE not has shapeshifter support. Normally with A1200 you should put in startup sequence in the top "prepareemul A1200" to start Shapeshifter.
With WinUAE you have direct support for Shapeshifter, so not need to modify startup-sequence.
Wtih FSUAE it seems that these solution not work

OSH · 06 March 2023, 12:50

I know, I'm using MuMove4K with prepareemul. But it doesn't help. ShapeShifter doesn't start but Fusion does. I haven't any idea why…

alexh · 06 March 2023, 13:23

Shapeshifter requires careful setup with 68060 or it does not work. (Because there were no 68060 Macs)

Depends which MacOS you are trying to use too. e.g. ShapeShifter + 68060 doesn't work at all with MacOS 8.1 (but does with 8.0)

OSH · 06 March 2023, 13:25

Yes, I know it. I'm focused on MacOS 7.6.1. Can you give me some advices?

alexh · 06 March 2023, 13:30

Have you turned off SUPERSCALER with your CPU config?

(Some of these may be MacOS 8.0 specific)

Have you changed the icon tool type to disable REMAP8K? Have you disabled the MacOS extension A/ROSE?

OSH · 06 March 2023, 22:53

Yes, SUPERSCALAR ist disabled. REMAP8K is disabled. A/ROSE was disabled. Nothing helps.

LIV2 · 07 March 2023, 09:36

Try the things listed here under "Nothing works! After starting ShapeShifter, I only get a white/gray/dithered gray screen."
https://shapeshifter.cebix.net/faq.html#General

It could be the Mac ROM you're using, try something like the Quadra 650 ROM

05 March 2023, 20:42	#1
OSH Registered User Join Date: Oct 2003 Location: Poland Age: 43 Posts: 142	TF360 and ShapeShifter and other questions Ok, I'm ran out ideas. I have TF360, and I want to launch ShapeShifter. But I can't. Everything I see is a grey screen. Nothing is loaded. I'm using MuLib package and MuEVD - but it doesn't work. And in MULTISCAN Productivity mode is quite slow. And second question: why I can't use CD-ROM? When I insert CD into CD drive, it doesn't start to rotate. So I can't make fresh Install of OS 3.9 SE under Amiga, I have to do this under FS-UAE. Anyone here has TF360? Which 060.library will be the best for this card?

06 March 2023, 13:23	#8
alexh Thalion Webshrine Join Date: Jan 2004 Location: Oxford Posts: 14,448	Shapeshifter requires careful setup with 68060 or it does not work. (Because there were no 68060 Macs) Depends which MacOS you are trying to use too. e.g. ShapeShifter + 68060 doesn't work at all with MacOS 8.1 (but does with 8.0) Last edited by alexh; 06 March 2023 at 13:30.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
TF360: 060 card for CD32	a4k-oerx	Hardware mods	79	19 August 2019 19:47
ShapeShifter	Doc Mindie	support.Apps	23	21 March 2018 17:41
ShapeShifter Help	coope1999	support.Apps	17	21 July 2015 07:18
Shapeshifter help! (Again?)	watertonian	support.Apps	18	27 May 2010 18:03
Shapeshifter	dkovacs	support.Apps	12	25 January 2006 01:25

05 March 2023, 23:15	#2
Akiko Registered User Join Date: Feb 2009 Location: UK Posts: 257	I have not tried ShapeShifter on my TF360 card yet, but perhaps it's the same issue that exists on the TF1260 and was resolved by a user on exxos? https://exxosforum.co.uk/forum/viewt...7a51b289547c71 The TF360 does not support the CD32 CD-ROM drive, at least not on the latest firmware, the TF360 developer Stephen Leary mentioned on his Youtube channel that he is actively looking for a fix, so hopefully if it's resolvable it will appear with the next firmaware update.

06 March 2023, 00:40	#3
OSH Registered User Join Date: Oct 2003 Location: Poland Age: 43 Posts: 142	No. ehide.device doesn't help. I can't load it via Loadmodule, because I loaded scsi.device too. And without scsi.device, I can't boot system.

06 March 2023, 04:55	#4
supaduper Registered User Join Date: Oct 2012 Location: Krypton Posts: 1,221	The CD does not work with the TF360 yet,did you not read the info that would have been provided to you when you purchased the board ? renember this is still in dev

06 March 2023, 12:31	#6
Seiya Registered User Join Date: Nov 2014 Location: Italy Posts: 2,435	FS-UAE not has shapeshifter support. Normally with A1200 you should put in startup sequence in the top "prepareemul A1200" to start Shapeshifter. With WinUAE you have direct support for Shapeshifter, so not need to modify startup-sequence. Wtih FSUAE it seems that these solution not work

06 March 2023, 12:50	#7
OSH Registered User Join Date: Oct 2003 Location: Poland Age: 43 Posts: 142	I know, I'm using MuMove4K with prepareemul. But it doesn't help. ShapeShifter doesn't start but Fusion does. I haven't any idea why…

06 March 2023, 13:25	#9
OSH Registered User Join Date: Oct 2003 Location: Poland Age: 43 Posts: 142	Yes, I know it. I'm focused on MacOS 7.6.1. Can you give me some advices?

06 March 2023, 13:30	#10
alexh Thalion Webshrine Join Date: Jan 2004 Location: Oxford Posts: 14,448	Have you turned off SUPERSCALER with your CPU config? (Some of these may be MacOS 8.0 specific) Have you changed the icon tool type to disable REMAP8K? Have you disabled the MacOS extension A/ROSE?

06 March 2023, 22:53	#11
OSH Registered User Join Date: Oct 2003 Location: Poland Age: 43 Posts: 142	Yes, SUPERSCALAR ist disabled. REMAP8K is disabled. A/ROSE was disabled. Nothing helps.

07 March 2023, 09:36	#12
LIV2 Tinkerer Join Date: Jan 2020 Location: NZ Posts: 104	Try the things listed here under "Nothing works! After starting ShapeShifter, I only get a white/gray/dithered gray screen." https://shapeshifter.cebix.net/faq.html#General It could be the Mac ROM you're using, try something like the Quadra 650 ROM

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)