A4000D Case Covers?

r.cade · 30 January 2008, 03:15

My old company I used to work for in the early 90's is moving and cleaned out the back room of all old parts.

I was given:
* 2 A4000's (one with Warp Engine 68040/40, one with T-Rex 68040/40)

* A half dozen other A4000 boards that do not seem to boot up.

* 2 3640 Rev. 3.1 Boards. One doesn't boot, the other seems to work fine but has (warm-up problem) written on it.

* A Phase 5 Cyberstorm Mk II - 68060/50 (!) Sadly, this doesn't boot up. Is there anything that needs done to a stock A4000 for this to work? Jumper settings, etc? Does it need RAM installed on it?

* Blizzard A1260 Card - 68060/50 - This one works!

* Bunches of other cards (AGA 2000 Flickerfixer, Fastlane Z3)

I don't really need all this stuff, so I am open for trades or sale. Also, both A4000's are complete except the top cases. Can you buy replacement top cases for these? Anyone have any?

alexh · 30 January 2008, 09:28

Quote:

Originally Posted by r.cade

* A Phase 5 Cyberstorm Mk II - 68060/50 (!) Sadly, this doesn't boot up. Is there anything that needs done to a stock A4000 for this to work? Jumper settings, etc? Does it need RAM installed on it

Yes, you need to change jumper settings.

http://phase5.a1k.org/files/CyberstormMK2_en.pdf

keropi · 30 January 2008, 09:31

and ram, I think it needs some ram too

r.cade · 30 January 2008, 15:12

Thanks very much for the manual. I think I already tried the INT/EXT jumpers in both positions, as the T-Rex requires it to be set to INT as well (the WarpEngine works with EXT). I'll give it another shot.

I don't have another removable 68060 chip to try that (the one on the Blizzard 1260 is soldered down). I almost tried an 040 and vice versa from the A3640, but that would have been bad due to the voltage difference.

30 January 2008, 03:15	#1
r.cade Registered User Join Date: Aug 2006 Location: Augusta, Georgia, USA Posts: 552	A4000D Case Covers? My old company I used to work for in the early 90's is moving and cleaned out the back room of all old parts. I was given: * 2 A4000's (one with Warp Engine 68040/40, one with T-Rex 68040/40) * A half dozen other A4000 boards that do not seem to boot up. * 2 3640 Rev. 3.1 Boards. One doesn't boot, the other seems to work fine but has (warm-up problem) written on it. * A Phase 5 Cyberstorm Mk II - 68060/50 (!) Sadly, this doesn't boot up. Is there anything that needs done to a stock A4000 for this to work? Jumper settings, etc? Does it need RAM installed on it? * Blizzard A1260 Card - 68060/50 - This one works! * Bunches of other cards (AGA 2000 Flickerfixer, Fastlane Z3) I don't really need all this stuff, so I am open for trades or sale. Also, both A4000's are complete except the top cases. Can you buy replacement top cases for these? Anyone have any?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
WTB: Clockport cable , A4000D Case	o0Nosferatu0o	MarketPlace	1	01 September 2012 01:43
A4000D in a Rackmount Case?	wXR	Hardware mods	3	26 December 2010 14:33
Jewel case inlets / covers	peo	request.Other	10	30 July 2009 01:07
WTB: Amiga 4000 top covers (or whole case)	r.cade	MarketPlace	2	01 September 2008 06:27
Wanted! CD32 Case and A1200 Case!	ElectroBlaster	MarketPlace	0	08 December 2002 18:28

30 January 2008, 09:31	#3
keropi . Join Date: Oct 2004 Location: Ioannina/Greece Posts: 5,040	and ram, I think it needs some ram too

30 January 2008, 15:12	#4
r.cade Registered User Join Date: Aug 2006 Location: Augusta, Georgia, USA Posts: 552	Thanks very much for the manual. I think I already tried the INT/EXT jumpers in both positions, as the T-Rex requires it to be set to INT as well (the WarpEngine works with EXT). I'll give it another shot. I don't have another removable 68060 chip to try that (the one on the Blizzard 1260 is soldered down). I almost tried an 040 and vice versa from the A3640, but that would have been bad due to the voltage difference.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)