A3000 SceenMode

attila06 · 10 February 2013, 18:26

Hello,

Sorry for my ignorance....but i only have 1200.

Firstly i have on my A3000 a kickstarter disk 2.0 and Wb 2.04 installed on my Hdd, I wanted to change my screenmode to try Super72, but how to do ?
In Wb 3.1 on my 1200 i put my Super72 in Devs/Monitors then i change my screenmode that's all, but here i can't.

Secondly does kickstarter disk 3.0 exits to install Wb3.1, if someone has please put it in the zone.

And to finish i don't understand why when i put a floppy in my drive it doesn't see anything.
i can see my floppy only if it's a boot disk.

Thanks in advance.

attila06 · 10 February 2013, 21:33

No one to help me ?

prowler · 10 February 2013, 21:36

You won't find anyone willing to upload a Kickstarter 3.0 disk to The Zone.

It's against the EAB rules (and so is asking for it

).

attila06 · 10 February 2013, 21:56

Ok thanks, but can you answer other questions

prowler · 10 February 2013, 22:01

No, sorry, but someone else here is bound to be able to help you with this if you wait a while.

mark_k · 10 February 2013, 22:13

I think the Super72 modes were first introduced with Workbench 3.0 (someone correct me if that's wrong), so you'd need to obtain a SuperKickstart 3.0/3.1 and Workbench 3.0/3.1 disk set in order to use them with your A3000.

Also, note that the scan rate of Super72 is about 24kHz. What type of monitor are you using with your A3000? Because most monitors would not be able to handle that scan rate.

attila06 · 11 February 2013, 16:40

Thanks Mark k ,

I'm going to try installing Wb2.1 until i'll have superkickstart 3.0.

Super72 was an example, i can't or i'm not able to add a screenmode with 2.04.

LocalH · 19 February 2013, 00:19

Quote:

Originally Posted by mark_k

I think the Super72 modes were first introduced with Workbench 3.0 (someone correct me if that's wrong)

According to the original set of 2.1 manuals I have here, the list of supported mode families: NTSC, PAL, Multiscan, A2024, Euro36, Euro72, Super72. Not sure if this support was present in 2.04 or earlier, however.

roy bates · 19 February 2013, 01:05

do you have a drawer called storage? have look inside see if its there.

10 February 2013, 18:26	#1
attila06 Zone Friend Join Date: Oct 2006 Location: Nice / France Posts: 206	A3000 SceenMode Hello, Sorry for my ignorance....but i only have 1200. Firstly i have on my A3000 a kickstarter disk 2.0 and Wb 2.04 installed on my Hdd, I wanted to change my screenmode to try Super72, but how to do ? In Wb 3.1 on my 1200 i put my Super72 in Devs/Monitors then i change my screenmode that's all, but here i can't. Secondly does kickstarter disk 3.0 exits to install Wb3.1, if someone has please put it in the zone. And to finish i don't understand why when i put a floppy in my drive it doesn't see anything. i can see my floppy only if it's a boot disk. Thanks in advance.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
a3000	lost_loven	support.Hardware	11	22 March 2010 01:20
FS: FULLY LOADED A3000, a bare bone A3000 and lots of Amiga Stuff!	emc_errol	MarketPlace	0	30 January 2009 22:33
What were A3000's good for?	Unknown_K	Retrogaming General Discussion	35	23 September 2006 23:56
Amiga fMSX Sceenmode Settings Trouble	CU_AMiGA	support.Apps	0	24 April 2005 15:20
A3000 Used	jmmijo	MarketPlace	13	09 April 2002 21:50

10 February 2013, 21:33	#2
attila06 Zone Friend Join Date: Oct 2006 Location: Nice / France Posts: 206	No one to help me ?

10 February 2013, 21:36	#3
prowler Global Moderator Join Date: Aug 2008 Location: Sidcup, England Posts: 10,300	You won't find anyone willing to upload a Kickstarter 3.0 disk to The Zone. It's against the EAB rules (and so is asking for it ).

10 February 2013, 21:56	#4
attila06 Zone Friend Join Date: Oct 2006 Location: Nice / France Posts: 206	Ok thanks, but can you answer other questions

10 February 2013, 22:01	#5
prowler Global Moderator Join Date: Aug 2008 Location: Sidcup, England Posts: 10,300	No, sorry, but someone else here is bound to be able to help you with this if you wait a while.

10 February 2013, 22:13	#6
mark_k Registered User Join Date: Aug 2004 Location: Posts: 3,344	I think the Super72 modes were first introduced with Workbench 3.0 (someone correct me if that's wrong), so you'd need to obtain a SuperKickstart 3.0/3.1 and Workbench 3.0/3.1 disk set in order to use them with your A3000. Also, note that the scan rate of Super72 is about 24kHz. What type of monitor are you using with your A3000? Because most monitors would not be able to handle that scan rate.

11 February 2013, 16:40	#7
attila06 Zone Friend Join Date: Oct 2006 Location: Nice / France Posts: 206	Thanks Mark k , I'm going to try installing Wb2.1 until i'll have superkickstart 3.0. Super72 was an example, i can't or i'm not able to add a screenmode with 2.04.

19 February 2013, 01:05	#9
roy bates Registered User Join Date: Apr 2011 Location: birmingham Age: 55 Posts: 2,827	do you have a drawer called storage? have look inside see if its there.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)