![]() |
![]() |
#1 |
Users Awaiting Email Confirmation
Join Date: Dec 2008
Location: leicester
Posts: 196
|
classicwb adv wont boot with 030 card in ?
hi,
I have installed classicwbadv onto hd but it wont play ball with my 030 card starts too boot but then just stops at a black screen . The card is fine with a normal w/b install and when i take card out classicwb loads fine ??? Anyone have any ideas ![]() |
![]() |
![]() |
#2 | |
PSPUAE DEV
|
Quote:
set echo on execute s:startup-sequence It will let you see what its loading before crashing. |
|
![]() |
![]() |
#3 |
Users Awaiting Email Confirmation
Join Date: Dec 2008
Location: leicester
Posts: 196
|
hi fol,
thanks for the reply, just done that and its guruing now when it gets to Fblit (tried a couple of times ) |
![]() |
![]() |
#4 | |
PSPUAE DEV
|
Quote:
Put a ; infront of it via "ed s:startup-sequence". In the sequence, you will find the fblit line. Then do the same, echo on etc etc. |
|
![]() |
![]() |
#5 |
Users Awaiting Email Confirmation
Join Date: Dec 2008
Location: leicester
Posts: 196
|
commented fblit out , it now gets to "intuition is trying to reset workbench etc" then wont go no further
do all the classicwb use fblit? |
![]() |
![]() |
#6 |
PSPUAE DEV
|
When it says "intuition is trying to reset blah blah", what happens when you press "cancel". Whats the last thing it loads before getting to that requester?
|
![]() |
![]() |
#7 |
Users Awaiting Email Confirmation
Join Date: Dec 2008
Location: leicester
Posts: 196
|
pressing cancel just leaves the startup seq on screen , last thing it trys to load is c:caprefs
|
![]() |
![]() |
#8 |
PSPUAE DEV
|
|
![]() |
![]() |
#9 |
Users Awaiting Email Confirmation
Join Date: Dec 2008
Location: leicester
Posts: 196
|
yes i understand where your coming from but at this rate ill be down to a barebones wb ,
![]() Hope this make sense and really appreciate your input ![]() |
![]() |
![]() |
#10 | |
PSPUAE DEV
|
Quote:
![]() You will then know exactly what things dont work, and look into it from there. Should have asked first, what Amiga are you running this on? |
|
![]() |
![]() |
#11 |
Users Awaiting Email Confirmation
Join Date: Dec 2008
Location: leicester
Posts: 196
|
Yes of course your right , specs are a1200 ,030 card with 8mb of ram ,6gb hd with 500mb wb partition and 3 partitions split between the rest all below 2gb
|
![]() |
![]() |
#12 |
Users Awaiting Email Confirmation
Join Date: Dec 2008
Location: leicester
Posts: 196
|
ok, can now boot to workbench
![]() Tried to open classact prefs but that gurued the machine ![]() so any ideas ![]() |
![]() |
![]() |
#13 |
Professional slacker!
|
@terexuk
Does your 030 card work if you boot from a Workbench floppy? |
![]() |
![]() |
#14 |
Users Awaiting Email Confirmation
Join Date: Dec 2008
Location: leicester
Posts: 196
|
yes will boot from floppy and also boots from hd using std wb install just classicwb is having problems
|
![]() |
![]() |
#15 |
PSPUAE DEV
|
|
![]() |
![]() |
#16 |
Users Awaiting Email Confirmation
Join Date: Dec 2008
Location: leicester
Posts: 196
|
its a A1200 MTec T1230/28 RTC Accelerator Card 8MB RAM
just out of interest the hd ran fine in winuae with same settings ![]() |
![]() |
![]() |
#17 |
Professional slacker!
|
Its very strange indeed as I used to have the very same card and ran Classic Workbench without issues.
As you're using >4gb did you patch the SCSI.Device? I wonder if this causes some issue with the M-Tec, do you have a CF-IDE or smaller HDD you can try? All the best, Steve. |
![]() |
![]() |
#18 | |
PSPUAE DEV
|
Quote:
|
|
![]() |
![]() |
#19 | |
Users Awaiting Email Confirmation
Join Date: Dec 2008
Location: leicester
Posts: 196
|
Quote:
Fitzsteve can you remember what settings you were using on card ie: the card at the moment is set to use async instead of 28/14mhz is this correct ? Anyways thanks for the help so far both of you much appreciated ![]() ![]() |
|
![]() |
![]() |
#20 |
Professional slacker!
|
Hey terexuk, no probs at all!
Firstly if you're using a HDD >4gb you need to patch the SCSI.Device as the default A1200 SCSI.Device only supports up to 4gb, this could be causing an issue. However if you have a smaller drive (or better still a CF for ease of setup) give that a try ![]() I don't remember what the settings were for on my old M-Tec, but I took this picture, and these are the settings I used: (click to see large image) ![]() |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Now my CF card wont boot.. I could cry | CritAnime | support.Hardware | 25 | 04 December 2011 03:33 |
Mysterious double boot ClassicWB ADV SP | Rishca | project.ClassicWB | 11 | 11 July 2011 17:25 |
classicwb adv | lambrettadave | project.ClassicWB | 7 | 27 October 2010 16:13 |
Files not found. ClassicWB ADV / WB 3.1 | Macca | project.ClassicWB | 3 | 24 May 2008 15:18 |
A1200 wont work stable if 030 card is removed? | ElectroBlaster | support.Hardware | 1 | 10 November 2003 00:02 |
|
|