04 September 2019, 19:24 | #1 |
Registered User
Join Date: Apr 2009
Location: N/A
Posts: 962
|
A500 (rev6a) 1MB chipRAM mod - avoid cutting JP7?
At the moment I am checking about mods to have an A500 rev6a motherboard see 1MB chipRAM instead of 512KB chipRAM and 512KB slowRAM. From what I understand one option is to cut JP2 pad 2 and 3 and solder pad 1 and 2 instead and cut JP7 pad 2 and 3.
However I have found this article which states there are ram cards out there which have jumpers which achieve same results as cutting JP7. My question is; how does this card (and possibly other cards as well) using a jumper achieve the same result as cutting JP7 on an A500 rev6a motherboard? |
04 September 2019, 20:25 | #2 |
Registered User
Join Date: Jun 2018
Location: Stockholm
Age: 48
Posts: 272
|
I believe it's like this:
To activate Expansion RAM (slow mem) the EXRAM line (pin 32 on A500 trapdoor connector) needs to be connected to ground since it is active low enable. With the jumper in place you ground the signal. When you remove the jumper or cut the trace (JP7A) the signal is no longer grounded and goes high, the 512k can then be used as chip mem provided JP2 is altered and you have a 1MB Fat Agnus chip installed (e.g. 8372A). Check pin 32 here: https://old.pinouts.ru/Motherboard/a...r_pinout.shtml The old A501 expansion boards have a JP1 solder jumper for enabling/disabling the EXRAM signal The EXRAM jumper has no relevance on a Rev8A A500+ motherboard, since it is treating any expansion ram as chip ram. |
06 September 2019, 06:43 | #3 | |
-
Join Date: Jul 2003
Location: Helsinki / Finland
Age: 43
Posts: 9,915
|
Quote:
This depends entirely on the configuration of the motherboard's other jumpers. It is possible to reconfigure the Rev 8A board to act as a 512/512 setup. You will need the EXRAM signal in that case for GARY to notify Agnus about the presence of c00000 RAM. |
|
06 September 2019, 19:57 | #4 | |
Registered User
Join Date: Apr 2009
Location: N/A
Posts: 962
|
My card does have a switch on/off. So regardless of what I do to JP7, if I make the JP2 modification then if I let the trapdoor card off it is recognized as chipRAM and if I turn it on it is recognized as slowRAM?
Quote:
|
|
07 September 2019, 12:16 | #5 |
Registered User
Join Date: Jun 2018
Location: Stockholm
Age: 48
Posts: 272
|
No, cutting JP7A means the jumper on the expansion card has no function (it is the same line but further down), so don't cut JP7A if you want to control this with a jumper on the expansion card. If you want to be able to easily revert back to 512k Chip + 512k Slow RAM then you can do something like this to JP2 (click and check picture) http://bax.comlab.uni-rostock.de/en/hardware/amiga500/
If you want both 1MB chip ram and slow ram (1,5MB) at the same time then you have Chris' or Pete's expansion ram solutions. It includes getting a gary adaptor. http://eab.abime.net/showthread.php?t=93130 http://eab.abime.net/showthread.php?t=85395 |
17 October 2021, 15:30 | #6 |
Registered User
Join Date: Sep 2021
Location: Belgrade, Serbia
Age: 46
Posts: 32
|
Sorry for ressurecting an old thread.
I have Amiga (rev5 board) that came with RocTec RM550C-F memory expansion board. I want to do a 1MB chip ram mod, so i got 8372A Agnus, and will cut a JP2 and add a surface mounted switch so it can be reversed. As this board doesn't have JP7A and i don't want to cut traces on it. I want to mod ram expansion so it can be seen as a chip ram. This board is configured to connect GND to EXRAM through 330ohm resistor and this is permanent. It has a switch that in ON position does nothing (connects EXRAM to GND through 330ohm resistor) because ON position has a trace between, on the other hand in OFF position it connects EXRAM to pin1 of expansion connector (5V). So if i cut permanent connection between solder pads of the switch will that enable chip ram or i have to do something more. |
17 October 2021, 17:32 | #7 |
-
Join Date: Jul 2003
Location: Helsinki / Finland
Age: 43
Posts: 9,915
|
Did you try just switching the RocTec trapdoor card off?
|
17 October 2021, 20:10 | #8 |
Registered User
Join Date: Sep 2021
Location: Belgrade, Serbia
Age: 46
Posts: 32
|
Update:
On rev. 6A board with 1MB chip memory mod done (JP2 upper two pads soldered and J7A cut), when trapdoor adapter is in OFF mode Amiga test kit reports 0.5chip 0.0fast 0.0slow, in ON mode it reports 1.0chip 0.0fast 0.0slow. I cut the trace on expansion card, removed the switch and installed jumper headers. With trace cut on trapdoor expansion and no jumper it reports 0.5chip 0.0fast 0.0slow, with jumper in ON mode it reports 1.0chip 0.0fast 0.0slow, with jumper in OFF mode it reports 0.5chip 0.0fast 0.0slow. Haven't tried on rev5 waiting for 8372A to arrive by the end of the week. Last edited by Misko78; 17 October 2021 at 20:47. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
a500 rev 5 1mb chipmem mod... confused | kipper2k | Hardware mods | 104 | 18 August 2023 09:33 |
A500 Rev5 1Mb Chip Ram Mod | gurth | Hardware mods | 13 | 07 July 2023 13:46 |
A500 rev 8a no boot after 1mb mod | timmyotool | support.Hardware | 0 | 03 March 2019 17:25 |
A500 Pro-RAM - 1MB ChipRAM or Not? | Sim085 | support.Hardware | 7 | 08 October 2018 22:55 |
A500 1mb Chipram Upgrade - Trapdoor problem | Amicol | Hardware mods | 6 | 07 February 2014 00:37 |
|
|