08 December 2013, 19:46 | #1 |
Registered User
Join Date: Oct 2013
Location: calgary canada
Posts: 11
|
kipper2k ide board and kickstart switch
im trying to have both my kickstart switch and kipper2k 8meg board with ide to both work. the kickstart switch is too tall and both boards wont fit together, I made a relocation cable to move it closer to the trapdoor so its out of the way, but my 1.3 works, when I switch to 3.1 I just get a red screen. I checked all pins and everything is good. anyone have any ideas?
|
08 December 2013, 20:02 | #2 |
R.I.P Smudge 18-08-16
Join Date: Aug 2005
Location: Leicester/UK
Age: 66
Posts: 3,968
|
Does the 3.1 chip work OK on it's own.
|
08 December 2013, 20:30 | #3 |
Registered User
Join Date: Oct 2013
Location: calgary canada
Posts: 11
|
works perfectly, and when the switch is plugged into the rom socket they both work perfectly. but when I plug it into the cable only 1.3 works, I have triple checked the cable, all pins on both ends are perfect.
|
08 December 2013, 23:42 | #4 |
Precious & fragile things
Join Date: Feb 2009
Location: Victoria, Australia
Posts: 1,946
|
You will have done a continuity check from each pin to each socket but also check that there's not two address lines tied together or something like that. Also that in the jiggling and moving one of the wires to the switch may have come loose and be just holding on.
|
08 December 2013, 23:51 | #5 |
Registered User
Join Date: Apr 2011
Location: birmingham
Age: 55
Posts: 2,827
|
hmm,i remember something about some kickstart switches not working properly with 1.3 and 3.1
did it work before with both? have you tried other kickstarts? |
09 December 2013, 00:00 | #6 |
Registered User
Join Date: Oct 2013
Location: calgary canada
Posts: 11
|
yes, same thing happens with 1.3 and 2.04. red screen on 2.04, 1.3 works, but both work plugged in to the socket. now I've seen quite a few other kickstart switches that are on a couple of inches of ribbon cable, so I don't know why this isn't working.
|
09 December 2013, 00:19 | #7 |
Registered User
Join Date: Oct 2013
Location: calgary canada
Posts: 11
|
and no matter which socket I install the kickstarts into, 1.3 works and the other doesn't. either left or right socket
|
09 December 2013, 03:03 | #8 |
Precious & fragile things
Join Date: Feb 2009
Location: Victoria, Australia
Posts: 1,946
|
The ribbon cable length is kept short to avoid timing issues on read.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Amiga 1000 kickstart (pal/ntsc switch) | frank_b | support.Hardware | 20 | 17 November 2015 17:27 |
Kickstart Switch / Dual Boot | craggus2000 | support.Hardware | 19 | 14 November 2010 07:30 |
Homebrew EPROM Kickstart board (pron for zetro et al.) | RedskullDC | Hardware mods | 9 | 09 January 2010 18:24 |
WTB: Kickstart Board for A1000 | Fingerlickin_B | MarketPlace | 24 | 18 April 2008 16:01 |
A500 (+) Kickstart switch with roms | FatterAgnus | MarketPlace | 7 | 21 March 2006 01:00 |
|
|