A 3000 Colours change when flicker fixer on in hires interlaced - Page 2

netizensmith · 20 September 2017, 16:12

Cheers. Corruption is that grey looking rectangle bottom right. I can see it fine on my phone when browsing this forum.<br />
<br />
I do at least have the bits needed to create the text probe you describe. Thanks.

Edit; corruption a red herring. Dpaint 4 plays it fine.

netizensmith · 22 September 2017, 22:27

Probing the suggested pins did not cause my LED to light up or flicker but it did cause the colours to change as I touched each pin.
Problem is with the RED channel. In the palette preferences, sliding the green and blue up and down the scale causes gradual colour changes; doing that with red though causes the colours to jump all over the place and also causes interference on the screen while I'm doing it.

fordav1 · 01 October 2017, 10:17

corruption points to bad flicker fixer RAM or connections to/from those RAMs as I mentioned in the post 2 weeks ago....

netizensmith · 01 October 2017, 13:08

Cheers. See my edit though. Corruption likely an incompatibility with dpaint 3. Issue narrowed down to red channel in flicker fixer mode. Tried investigating as per instructions but no led activity (see above).

20 September 2017, 16:12	#21
netizensmith Registered User Join Date: Sep 2017 Location: England Posts: 23	Cheers. Corruption is that grey looking rectangle bottom right. I can see it fine on my phone when browsing this forum.<br /> <br /> I do at least have the bits needed to create the text probe you describe. Thanks. Edit; corruption a red herring. Dpaint 4 plays it fine. Last edited by netizensmith; 20 September 2017 at 17:45.

22 September 2017, 22:27	#22
netizensmith Registered User Join Date: Sep 2017 Location: England Posts: 23	Probing the suggested pins did not cause my LED to light up or flicker but it did cause the colours to change as I touched each pin. Problem is with the RED channel. In the palette preferences, sliding the green and blue up and down the scale causes gradual colour changes; doing that with red though causes the colours to jump all over the place and also causes interference on the screen while I'm doing it. Last edited by netizensmith; 22 September 2017 at 22:33.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
>16 colours per line in hires?	drhex	Coders. Asm / Hardware	19	05 February 2016 10:23
Scanline flicker when moving between interlaced and non-interlaced WB screens	mr_a500	support.FS-UAE	0	19 December 2014 17:10
switch to hires and double when interlaced screen is displayed	turrican3	request.UAE Wishlist	6	19 June 2009 13:22
FS: Scandoubler/Flicker Fixer DCE Flicker Magic	lopos2000	MarketPlace	15	23 October 2007 11:18
ToastScan Flicker Fixer Clarity Vs. Amiga 3000	atrionfo	support.Hardware	7	22 March 2007 01:08

01 October 2017, 10:17	#23
fordav1 Registered User Join Date: Jan 2017 Location: Australia Posts: 84	corruption points to bad flicker fixer RAM or connections to/from those RAMs as I mentioned in the post 2 weeks ago....

01 October 2017, 13:08	#24
netizensmith Registered User Join Date: Sep 2017 Location: England Posts: 23	Cheers. See my edit though. Corruption likely an incompatibility with dpaint 3. Issue narrowed down to red channel in flicker fixer mode. Tried investigating as per instructions but no led activity (see above).

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)