problems mouting a pc disk

15 December 2002, 14:57

ok i was following the guide at http://ale.emuunlim.com/get-kick-rom.htm, but when i type mount pc0: it returns an error Device 'pc0:' not found in the file 'DEVS:MountList' so it might have something to do with me beeing a total newbie

, but what do i do to get my pc disk mouted so i can get the kickrom to my pc ?
its an amiga 600 with 2 Mb ram and workbench 2.1

andreas · 15 December 2002, 19:06

AFAIK, pc0: is a device handled by CrossDOS.
As CrossDOS *should* (?) be part of WB 2.x, I think it might not be properly installed.
But that's only an assumption.

RetroMan · 15 December 2002, 19:12

CrossDos is only part of 2.1, not 2.04

15 December 2002, 19:30

well i looked through the manual but i cant see crossdos or mount mentioned anywhere

RetroMan · 15 December 2002, 19:34

to use CrossDos, there should be a file called PC0 in DEVS:DOSDRIVERS or STORAGE:DOSDRIVERS ! Go and check for it :)

15 December 2002, 21:05

ok now i got the drive mouted thx for the help
next problem :-)
when i write TRANSROM RAM:KICK.ROM it starts typing a lot of encrypted stuff on the screen for about 5 mins, then afterwards there are no file named kick.rom on my ram:

any ideas ?

Severin · 15 December 2002, 21:23

ok, there's 2 things you could try...

1. redirect the output eg. TRANSROM >RAM:KICK.ROM

2. use saverom (attached) eg. saverom ram:kick.rom

RetroMan · 15 December 2002, 22:07

Yup

Severin is correct, ">" should do the trick here

16 December 2002, 00:18

Thanks for the help guys now it works

15 December 2002, 14:57	#1
Maniac99 Posts: n/a	problems mouting a pc disk ok i was following the guide at http://ale.emuunlim.com/get-kick-rom.htm, but when i type mount pc0: it returns an error Device 'pc0:' not found in the file 'DEVS:MountList' so it might have something to do with me beeing a total newbie , but what do i do to get my pc disk mouted so i can get the kickrom to my pc ? its an amiga 600 with 2 Mb ram and workbench 2.1

15 December 2002, 19:34	#5
RetroMan Registered User Join Date: Aug 2001 Location: Germany Age: 51 Posts: 3,704	to use CrossDos, there should be a file called PC0 in DEVS:DOSDRIVERS or STORAGE:DOSDRIVERS ! Go and check for it :) Last edited by RetroMan; 15 December 2002 at 22:06.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Problems reading Jaz disk	Rod_cl	support.Hardware	12	30 July 2015 15:51
Floppie disk problems	whitegiant89	support.Hardware	6	06 March 2010 22:17
Disk reading problems	Galahad/FLT	support.WinUAE	18	15 November 2009 12:32
Zip mouting	Poporopo	request.UAE Wishlist	7	12 March 2007 18:57
O.S 3.9 Hard disk problems	adgloride	request.Apps	5	19 September 2004 00:44

15 December 2002, 19:06	#2
andreas Zone Friend Join Date: Jun 2001 Location: Germany Age: 50 Posts: 5,857	AFAIK, pc0: is a device handled by CrossDOS. As CrossDOS should (?) be part of WB 2.x, I think it might not be properly installed. But that's only an assumption.

15 December 2002, 19:12	#3
RetroMan Registered User Join Date: Aug 2001 Location: Germany Age: 51 Posts: 3,704	CrossDos is only part of 2.1, not 2.04

15 December 2002, 19:30	#4
Maniac99 Posts: n/a	well i looked through the manual but i cant see crossdos or mount mentioned anywhere

15 December 2002, 21:05	#6
Maniac99 Posts: n/a	ok now i got the drive mouted thx for the help next problem :-) when i write TRANSROM RAM:KICK.ROM it starts typing a lot of encrypted stuff on the screen for about 5 mins, then afterwards there are no file named kick.rom on my ram: any ideas ?

15 December 2002, 22:07	#8
RetroMan Registered User Join Date: Aug 2001 Location: Germany Age: 51 Posts: 3,704	Yup Severin is correct, ">" should do the trick here

16 December 2002, 00:18	#9
Maniac99 Posts: n/a	Thanks for the help guys now it works

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)