English Amiga Board


Go Back   English Amiga Board > Support > support.Hardware

 
 
Thread Tools
Old 25 March 2013, 17:31   #1
Hockmiester
 
Posts: n/a
Moving HDD from Pc to Amiga

Afternoon all. Please post me a link if this has been answered before.

I've spent a productive day (unproductive in my wife's eyes) creating a CF HDD using WinUAE for use in a Amiga 600 37.300. I have misplaced the workbench disks (I managed to find the manual). I can buy more but wanted to start immediately using the PC and moving the HDD to the Amiga.

After a lot of trial and error I managed to clear the PC partitions on the CF in the command prompt and setup the CF drive in WinUAE with help of the forum.

Workbench 2.1 is installed on 1 of the partitions (HD0 as bootable) and if I close WinUAE fully and run it again selecting only the HDD (no floppies) it boots to workbench and shows all my wonderful partitions/drives.

I used all the same parameters in WinUAE as my actual Amiga including RAM setup etc.

I have a IDE board. For full disclosure I'm not sure if the jumper is on 1/2 or 2/3 but on 1 setting the LED doesn't light nor does the Disk light on the Amiga and on one setting both the LED and the Amiga lights flash so I'm assuming this is the correct jumper setting (I have tried both anyway).

I insert the CF HDD created in WinUAE and the Amiga just shows the purple kickstart screen with the floppy disk.

I must be close. What am I doing wrong.
 
Old 25 March 2013, 17:34   #2
fitzsteve
Professional slacker!
fitzsteve's Avatar
 
Join Date: Jul 2009
Location: Kent, UK
Age: 41
Posts: 6,613
Send a message via MSN to fitzsteve
Did you try a quick CTRL-A-A (A = Amiga Key) reset? Does it start to boot then?

Some CF cards act like this, Kingston with the flower logo mostly...

Next thing to try, when you setup your partition did you tick 'bootable' for your boot partition?
fitzsteve is online now  
Old 25 March 2013, 17:37   #3
Hockmiester
 
Posts: n/a
Before I spotted your reply (very fast thanks). I just tried running WinUAE as mentioned in my original post. Everything works.

However, if I run WinUAE.exe as administrator and load the HDD as above. I get the Kickstart screen.

Closing and running the .exe not as administrator to double check and the HDD boots to workbench.

Is this a factor?
 
 


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Similar Threads
Thread Thread Starter Forum Replies Last Post
Moving WB installation from HDD to CF - Help required manicx support.Apps 6 18 April 2011 14:21
Missing something moving to real amiga webmany project.ClassicWB 7 25 May 2010 08:05
'clone' virtual HDD in winuae to real Amiga HDD? gizmomelb support.Other 1 11 December 2009 09:13
geek moving to amiga os 4 (plattform) PseudoDOS Amiga scene 8 03 August 2004 17:16
It's moving..it's alive, it's moving.. IT'S ALLIIIIIIIIIIVE!!!!!!!!!1 alkis21 Retrogaming General Discussion 23 22 August 2002 10:51

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +2. The time now is 20:10.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2021, vBulletin Solutions Inc.
Page generated in 0.07263 seconds with 13 queries