Video Toaster 2000 startup error

triskalguilo · 12 July 2013, 20:40

I have an A2000, and I've installed a SCSI card, an 8MB fast RAM card, and a SCSI hard drive into it. I then installed a Video Toaster 2000 card, as well as installing its software (which is version 2.0).

All of that stuff installed perfectly, but when I try to start the Video Toaster software, it gives an error that says something like "could not obtain chip memory".

I've read that the Video Toaster needs at least 1MB of chip RAM in order to start up. My A2000 has a total of 1MB of RAM on the motherboard, which SysInfo identifies as 512KB chip and 512KB slow.

As far as I know, all of the chips are stock, except that I upgraded the KickStart from 1.2 to 2.04, and the Agnus from 8370 to 8372A. Even after these upgrades, SysInfo still says 512KB chip and 512KB slow.

What can I do to get this Video Toaster running? Is there something that I can do to get that whole 1MB of RAM to show up as chip RAM? Are there software patches or utilities that I can run? Are there additional chip upgrades that I can do? Help!

I did read that you should move jumper J101 from pins 1-2 to pins 2-3, but when I tried that, it gets stuck on a gray screen while starting up. It never gets to the point of DOS or Workbench starting.

triskalguilo · 12 July 2013, 20:54

I found this post that says that J101 should be set to 1-2 and J500 should be open:

http://www.amiga.org/forums/showpost...88&postcount=7

However, there are no jumper pins for J500 on my motherboard. It looks like the connection is made right on the motherboard via a circuit pathway. So, is it true that I need to open J500, and if so, how do I do that?

Jope · 12 July 2013, 21:02

With a knife. Just scratch through the little bit of foil that connects the two pads. No need to dig a big hole, scrape just enough that the connection is broken.

And be careful that the knife doesn't slip. Don't cut anything but that connection.

amiman99 · 12 July 2013, 22:58

When you get the 1MB chip RAM to work, make sure you change the screen resolution to 640x200 4color. This will free up valuable chip ram.

videofx · 13 July 2013, 07:48

Look for an Icon called Auto Hue where you clicked on the toaster icon. Auto hue needs to be run before the toaster will operate.

r.cade · 13 July 2013, 16:18

You will need more RAM. Do the mod to get to 1M chip, and then get a card with at least 2M of fast RAM or else it won't function.

emufan · 15 July 2013, 18:45

Quote:

Originally Posted by r.cade

You will need more RAM. Do the mod to get to 1M chip, and then get a card with at least 2M of fast RAM or else it won't function.

i was wondering too, but then i saw the info he gave in 1st posting:

Quote:

Originally Posted by triskalguilo

I have an A2000, and I've installed a SCSI card, an 8MB fast RAM card, and a SCSI hard drive into it.

with the 1MB chip plus 8MB fast the machine has enough ram for a start

triskalguilo · 21 July 2013, 08:50

Just letting everyone know that I cut open J500 and moved J101 to position 2-3, and now the full 1MB shows up as chip RAM, and the Video Toaster starts just fine. Note that this was on a B2000-CR revision 4.4 motherboard. Thanks for the tips, everyone

12 July 2013, 20:40	#1
triskalguilo Registered User Join Date: Jul 2013 Location: Springfield, MO, USA Posts: 23	Video Toaster 2000 startup error I have an A2000, and I've installed a SCSI card, an 8MB fast RAM card, and a SCSI hard drive into it. I then installed a Video Toaster 2000 card, as well as installing its software (which is version 2.0). All of that stuff installed perfectly, but when I try to start the Video Toaster software, it gives an error that says something like "could not obtain chip memory". I've read that the Video Toaster needs at least 1MB of chip RAM in order to start up. My A2000 has a total of 1MB of RAM on the motherboard, which SysInfo identifies as 512KB chip and 512KB slow. As far as I know, all of the chips are stock, except that I upgraded the KickStart from 1.2 to 2.04, and the Agnus from 8370 to 8372A. Even after these upgrades, SysInfo still says 512KB chip and 512KB slow. What can I do to get this Video Toaster running? Is there something that I can do to get that whole 1MB of RAM to show up as chip RAM? Are there software patches or utilities that I can run? Are there additional chip upgrades that I can do? Help! I did read that you should move jumper J101 from pins 1-2 to pins 2-3, but when I tried that, it gets stuck on a gray screen while starting up. It never gets to the point of DOS or Workbench starting.

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Installing Video Toaster v1.0 software on a B-2000	tesla	support.Other	48	25 April 2013 05:43
Video Toaster 2000 software	chfriend	request.Apps	5	25 March 2012 04:58
DiscreetFX brings you another classic NewTek video about the Amiga Video Toaster 2.0.	Pyromania	Amiga scene	3	13 October 2007 00:42
FS/FA: ICD Flicker Free Video/Scandoubler for Amiga 500,1000,2000,Toaster	vamigan	MarketPlace	5	22 September 2007 03:37
Attn ASM Coders: NewTek promo video for Amiga Video Toaster	Pyromania	Coders. General	1	02 June 2007 02:02

12 July 2013, 20:54	#2
triskalguilo Registered User Join Date: Jul 2013 Location: Springfield, MO, USA Posts: 23	I found this post that says that J101 should be set to 1-2 and J500 should be open: http://www.amiga.org/forums/showpost...88&postcount=7 However, there are no jumper pins for J500 on my motherboard. It looks like the connection is made right on the motherboard via a circuit pathway. So, is it true that I need to open J500, and if so, how do I do that?

12 July 2013, 21:02	#3
Jope - Join Date: Jul 2003 Location: Helsinki / Finland Age: 42 Posts: 9,454	With a knife. Just scratch through the little bit of foil that connects the two pads. No need to dig a big hole, scrape just enough that the connection is broken. And be careful that the knife doesn't slip. Don't cut anything but that connection.

12 July 2013, 22:58	#4
amiman99 Registered User Join Date: Sep 2009 Location: San Antonio, TX USA Age: 49 Posts: 1,162	When you get the 1MB chip RAM to work, make sure you change the screen resolution to 640x200 4color. This will free up valuable chip ram.

13 July 2013, 07:48	#5
videofx Registered User Join Date: Jan 2013 Location: Chicago, IL USA Posts: 585	Look for an Icon called Auto Hue where you clicked on the toaster icon. Auto hue needs to be run before the toaster will operate.

13 July 2013, 16:18	#6
r.cade Registered User Join Date: Aug 2006 Location: Augusta, Georgia, USA Posts: 523	You will need more RAM. Do the mod to get to 1M chip, and then get a card with at least 2M of fast RAM or else it won't function.

21 July 2013, 08:50	#8
triskalguilo Registered User Join Date: Jul 2013 Location: Springfield, MO, USA Posts: 23	Just letting everyone know that I cut open J500 and moved J101 to position 2-3, and now the full 1MB shows up as chip RAM, and the Video Toaster starts just fine. Note that this was on a B2000-CR revision 4.4 motherboard. Thanks for the tips, everyone

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)