![]() |
![]() |
#1 |
Posts: n/a
|
Battery leakage on Amiga 500+
Hi Folks,
First post so be kind! I've picked up what looked like a pristine Amiga 500+. Before I opened it I checked it was all working by running Workbench and Lemmings for a few hours. Once opened I could see that the rev8a motherboard had a mildly leaking battery. I've removed it and cleaned up the motherboard and components nearby with alcohol and have moved onto checking continuity on the tracks that have some corrosion on them. I've attached a picture of the area. In the picture the corrosion looks really bad, it doesn't look that bad in real life the picture seems to bring out the worst. Can anyone tell me where I can check continuity for the pads circled in red please? I'll look at recapping it if this area is okay. Thanks, AngryInca |
![]() |
#2 |
Registered User
Join Date: Aug 2007
Location: USA
Posts: 359
|
Perhaps you can look here for the pads that you have circled?
http://beta.amigapcb.org/ It doesn't look that bad too me, I have seen much worse. Congratulations! |
![]() |
![]() |
#3 | |
Posts: n/a
|
Quote:
|
|
![]() |
#4 |
Global Moderator
Join Date: Aug 2008
Location: Sidcup, England
Posts: 10,300
|
AngryInca, you are one very fortunate A500+ owner.
![]() I recently acquired an A500+ with the seals still intact, but when I opened it up to remove the battery to prevent the inevitable damage which would soon ensue, I was far too late as evidenced by a wasteland of green residue four inches in diameter all around the corroded battery! ![]() |
![]() |
![]() |
#5 |
Registered User
Join Date: Jan 2018
Location: Gloucester
Posts: 83
|
AngryInca, that looks a nice easy fix.
I would be tempted to not test for continuity, and simply to run trace wires along the paths. The top one in the photo - circled red, closest to the battery - appears to run under the Gary chip so may be most time consuming (Pin 11 of Gary IF I am reading beta.amigapcb.org rev 8a correctly!) - the others look like two resistors and one solder pad that they run to, so should be a doddle. ![]() |
![]() |
![]() |
#6 |
Registered User
Join Date: Jan 2018
Location: Gloucester
Posts: 83
|
|
![]() |
![]() |
#7 |
Lorraine Lover
Join Date: Feb 2018
Location: DeBary U.S.
Posts: 5
|
Capping
Wow, that board looks almost pristine. You have a few partially (but minimally so) corroded traces that really shouldn't give you any problems. If the one nearest the single battery hole has continuity then you're all set. May I suggest, when it comes to standard electrolytic capacitors (axial & radial) recapping is hardly ever needed. If you don't see any corrosion (from the battery) at the cap's leads they're almost always OK to leave undisturbed, and I don't think your board has any of the surface mount type (which are the ones that "leak" in every sense of the word.) Congratulations on your find, I sure wish I had been that lucky with my last Amiga purchase.
Last edited by Ric; 11 February 2018 at 20:50. |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Best solution to remove crystallic acid from battery leakage | Reynolds | support.Hardware | 17 | 03 May 2016 14:24 |
A500+ Battery Leakage | psygnosis | support.Hardware | 10 | 13 April 2013 15:12 |
Repairing A2000 from battery leakage | TjLaZer | support.Hardware | 2 | 04 June 2012 20:13 |
A2500 battery leakage cleanup | Dreamcast270mhz | support.Hardware | 10 | 29 December 2009 05:59 |
A500+ is......dead? (Battery leakage) | Smiley | support.Hardware | 17 | 05 September 2007 01:55 |
|
|