01 December 2004, 19:01 | #1 |
Moderator
Join Date: Sep 2004
Location: France
Age: 51
Posts: 4,277
|
Hardware plan of loriciel's phaser (for westphaser&Crazy shot)
Hy Guys
I am looking for printed board of loriciel's phaser because I can't buy it (it's very hard to found) It's must be not very complex to do If somebody have it, can you send it to me? bye |
01 December 2004, 19:42 | #2 |
Mehh :D
Join Date: Nov 2004
Location: Bristol, SW UK
Age: 61
Posts: 242
|
For this project you will need the original circuit board one from a broken one perhaps? You take off all the components and make notes of how and where these components go - making a "parts list" is good at this point. You then scan the bare circuit board (both sides if double sided). Use PSP to make a negative image and clean it up, then print the artwork onto transparent film. Place transparent film onto photosensitive PCB board, expose as normal, etch and drill. Replace all the parts as per the parts list (using new components of course) and there ya go.
Like you said, it's not hard to do, but extremely time consuming. It does give you a nigh on perfect replica though, better than a "ebuild" where you take the circuit diagram, load it into an auto-router type program and re-design a new circuit board. here is one from a Sectrum that I did - took three weeks, and it really is all my own work, done as described above. Forget the thumbnail, can't figure out how to attach it. Uploaded to Zone instead...... Comments welcome?? Last edited by lloyd; 01 December 2004 at 19:43. Reason: how do you attach a thumbnail? |
01 December 2004, 20:19 | #3 | |||
Moderator
Join Date: Sep 2004
Location: France
Age: 51
Posts: 4,277
|
Quote:
Quote:
Quote:
Last edited by CFou!; 01 December 2004 at 20:25. |
|||
01 December 2004, 20:26 | #4 |
Mehh :D
Join Date: Nov 2004
Location: Bristol, SW UK
Age: 61
Posts: 242
|
Do you have the circuit diagram? If so, you can design a new PCB. Have a look at http://www.seattlerobotics.org/encod...bsoftware.html
What did you think of my Spectrum PCB? Specbot.gif, uploaded to the Zone.... Is this the kind of thing you are after? |
01 December 2004, 21:57 | #5 | |
Moderator
Join Date: Sep 2004
Location: France
Age: 51
Posts: 4,277
|
Quote:
|
|
01 December 2004, 22:06 | #6 |
Mehh :D
Join Date: Nov 2004
Location: Bristol, SW UK
Age: 61
Posts: 242
|
Have you ever seen one?
Does it look like this - this is for the STE tho... http://cgi.ebay.co.uk/ws/eBayISAPI.d...tem=8134466742 |
01 December 2004, 22:20 | #7 |
Posts: n/a
|
Sega's phaser looks awfully similar to that one:
http://cgi.ebay.co.uk/ws/eBayISAPI.d...sPageName=WDVW And sega master system pads were %100 amiga compatible. Because this one connects to the gamepad port on sega master system, it can probably be used on amiga and might be similar to the one you are looking. |
02 December 2004, 15:00 | #8 |
Mehh :D
Join Date: Nov 2004
Location: Bristol, SW UK
Age: 61
Posts: 242
|
looks awfully like the Sinclair version too - I have one somewhere. Wonder if all these phasers are the same, just a different plug???
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Which consoles have you kept, sold, plan to sell or plan to buy | amigapd | Retrogaming General Discussion | 17 | 29 December 2012 09:22 |
A plan to relive the Magazine & Coverdisk days | diablothe2nd | Retrogaming General Discussion | 10 | 06 November 2012 12:41 |
Crazy USB Link Hardware Emulation Idea | Djay | Hardware mods | 1 | 26 December 2010 02:33 |
aminet & amiga Plus cds - floppy & cd software/games - hardware & magazines for SALE! | bastibs | MarketPlace | 1 | 07 May 2008 11:33 |
Loriciel Light Phaser | lloyd | support.Hardware | 10 | 03 December 2004 13:20 |
|
|