![]() |
![]() |
#1 |
Da Digger :)
Join Date: Nov 2008
Location: Monza, Italy
Posts: 2,822
|
A600 Keyboard LEDS cable
Hi,
I have a little problem: after keeping my A600 case open for a long time, I noticed that two cables (out of 4) are detached. They are the orange and red cables (see photo). I suppose the 4-pins connector is used for LEDS power (POWER, FLOPPY, DISK). There are 2 soldering points, and I don't remember which one is for the red cable and which one for the orange one... ![]() Last edited by Supamax; 27 June 2011 at 02:34. |
![]() |
![]() |
#2 |
Registered User
Join Date: Sep 2006
Location: Thunder Bay, Canada
Posts: 4,323
|
Hi,
looking at your picture... Red is top left, Orange is bottom left |
![]() |
![]() |
#3 |
Da Digger :)
Join Date: Nov 2008
Location: Monza, Italy
Posts: 2,822
|
ok
![]() thanks mate! |
![]() |
![]() |
#4 |
Registered User
Join Date: Aug 2010
Location: Newcastle Australia
Age: 63
Posts: 18
|
This is a pain with the 600 as the lead has very short, fine gauge wires and is awkward to unplug. After mine breaking a couple of times I added an extension section to make it more secure. Just got some ribbon cable in matching colours and some thin tube heatshrink to insulate the joins.
![]() |
![]() |
![]() |
#5 | |
Da Digger :)
Join Date: Nov 2008
Location: Monza, Italy
Posts: 2,822
|
Quote:
![]() Where did you buy the heatshrink tube? Electronics store? P.S. I saw that your cables colors are different. I thought they were color-coded the same way worldwide... |
|
![]() |
![]() |
#6 |
Registered User
Join Date: Aug 2010
Location: Newcastle Australia
Age: 63
Posts: 18
|
Hi Supamax,
yes most electronics stores where you might buy components, gadgets, etc should carry small assorted packs of heatshrink tube in various colours and sizes. A hairdryer is sufficient to cause it to shrink and make a nice, neat insulated join. Just had another look at your pic, I think they're the same; green, orange, red, black. Maybe the quality of my pic, a very old digicam! Cheers mutch. Last edited by mutch; 10 July 2011 at 03:02. |
![]() |
![]() |
#7 |
Registered User
Join Date: Feb 2007
Location: Melbourne, Australia
Age: 41
Posts: 3,773
|
I personally use a cigarette lighter, there has been a couple of times when I've accidentally set fire to the wire though.
![]() |
![]() |
![]() |
#8 |
Precious & fragile things
Join Date: Feb 2009
Location: Victoria, Australia
Posts: 1,946
|
Hairdryers be damned, cigarette lighters are the only way to go
![]() |
![]() |
![]() |
#9 |
-
Join Date: Jul 2003
Location: Helsinki / Finland
Age: 44
Posts: 9,961
|
I use a lighter to melt heatshrink too. :-)
I've been told that it's not the right way to do it, but just be quick with the flame so that it shrinks and then stop and no-one will know the difference. ;-) |
![]() |
![]() |
#10 |
Registered User
Join Date: Nov 2009
Location: Blyth England
Age: 68
Posts: 786
|
I've never tried the lighter method, I normally use a soldering iron after I soldered the wires together. That works ok as long as you don't use the part of the tip that has solder on it (messy if you do).
I reckon that a hot air soldering station would do a great job with heatshrink tubing but I haven't tried that yet. |
![]() |
![]() |
#11 |
I hate potatos and shirts
|
Used all the mentioned methods. The best is using a SMD rework station, but that's an overkill if you are using it only to heat shrink some insulation.
So, here comes my cigarette lighter (yes, I'm a smoker). |
![]() |
![]() |
#12 |
Da Digger :)
Join Date: Nov 2008
Location: Monza, Italy
Posts: 2,822
|
|
![]() |
![]() |
#13 |
Registered User
Join Date: May 2001
Location: ?
Posts: 19,665
|
I got tired of this problem and directly replaced those tiny cables with long ones. It's a lifesaver.
I recommend you do the same, specially if you open the A600 frequently (like I do). |
![]() |
![]() |
#14 | |
Posts: n/a
|
Quote:
|
|
![]() |
#15 |
Registered User
Join Date: Aug 2013
Location: Croatia
Age: 43
Posts: 341
|
They both produce heat which is needed for heatshrink tube to shrink?
|
![]() |
![]() |
#16 | |
Precious & fragile things
Join Date: Feb 2009
Location: Victoria, Australia
Posts: 1,946
|
There's my original quote, troll, notice the absence of an 'e' before cigarette.
Quote:
Heatguns are also a viable option depending on the distance from plastic parts, a hairdryer just doesn't get hot enough. |
|
![]() |
![]() |
#17 |
Registered User
Join Date: Jun 2016
Location: Pittsburgh
Posts: 5
|
Bumping an age old thread... Anyway, Thanks! Ripped my wires off and just wasn't sure. This was the info I needed! All working great again.
|
![]() |
![]() |
#18 |
Registered User
Join Date: Jul 2013
Location: Liverpool
Posts: 2,608
|
Just for Ref...
Last edited by Nobby_UK; 12 April 2020 at 23:42. |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
[Absolute last resort] Solution to A600 (maybe 1200?) keyboard cable problem | Amiga1992 | support.Hardware | 134 | 21 September 2020 23:47 |
WTB- A600 Keyboard Membrane Or Full Keyboard! | hansel75 | MarketPlace | 1 | 02 November 2012 06:51 |
Want to Buy - A600 Keyboard (Blue cable type) | kipper2k | MarketPlace | 4 | 21 April 2012 19:00 |
Miracle keyboard cable pinouts? | mmikko | support.Hardware | 4 | 10 September 2009 22:59 |
configurable keyboard leds | debbuthap | support.WinUAE | 6 | 01 March 2003 22:40 |
|
|