![]() |
![]() |
#1 |
Registered User
Join Date: Jun 2019
Location: AUS
Posts: 29
|
Amiga CD32 No Composite Signal
Hey All,
I have recently purchased a 'faulty' CD32 which I am now in the last stages of restoring. I recapped and cleaned up the board, a lot of leakage unfortunately. (Thankfully I also became aware of the 2 reversed caps before I started). After the re-cap I was able to test it through S-Video and its working fine. Even the CD drive is reading discs correctly. One issue is that I am just not getting composite signal, the schematics are not that complicated so I don't understand what I'm missing. I've tested using a composite port directly on a screen and also through a RetroTink 2X Pro. I have tried:
The CXA1145 encoder (U12) is giving 2.2v from the CV_OUT pin (20), whats weird is that I can have voltage at the RCA jack until I wire it up to test then it seems to give nothing: 0v and doesn't seem to charge back up to 2v unless I leave it powered off for a while and switch it back on. I was going crazy thinking I was chasing a short for ages.. but I think this may be normal ? On some further testing I can get a signal if I connect LUMA to the RCA but then S-Video quality is reduced. Does 2v seems correct for a composite signal? Any ideas what could be missing? I have a feeling that some via got corroded or something, but I dunno where to look at this stage I know all this is only for crappy composite, and I've already spent too many hours trying to figure it out but I want to get it back together as a fully working CD32 machine one and for all.. Any suggestions on what to look out for? it would be much appreciated! Thanks! |
![]() |
![]() |
#2 |
Registered User
Join Date: Jan 2004
Location: Yorkshire
Posts: 772
|
C-Sync issue? check continuity between pin 80 of Alice and pin 10 of the encoder.
edit: then again, it must be working if you're getting a sync on luma. edit: Looking at the CXA1145 datasheet I think the delay line might be the problem? or maybe something with C459/R459/C460/R222/R224 or the VVref voltage. If it's a faulty delay line then the easiest thing to do is to do is replace the CXA1145 with a Rohm BH7236, remove all of the delay line, band pass filter & iref/vref parts, you'll need to remove C214 as well. Then put a 22pf capacitor in C222 and a 68uH inductor in R223. Additionally, for the CD32 you'll need to connect the Chroma and Luma outputs directly to C281/C282 and remove all of the stuff that's inbetween. Rohm recommends C281 to be 220uF, C282 to be 0.047uF and R283/R285 to be 75 ohm but it might be fine stock. Last edited by Mick; 15 July 2024 at 16:05. |
![]() |
![]() |
#3 |
Registered User
Join Date: Oct 2012
Location: Krypton
Posts: 1,230
|
As mentioned above as you get S-Video but no Composite then I will say the Delay line circuit is the fault so just replace the CXA1145 with a CXA2075M encoder as has the delay line built into it
[ Show youtube player ] |
![]() |
![]() |
#4 |
Registered User
Join Date: Jun 2019
Location: AUS
Posts: 29
|
Thanks so much Mick and Supaduper,
I'll take a look into this and let you know how I get on! |
![]() |
![]() |
#5 |
Registered User
Join Date: Jan 2004
Location: Yorkshire
Posts: 772
|
CXA2075 will work as well but I would recommend using an external Y trap (22pF capacitor and 68uH inductor) for better picture quality.
Last edited by Mick; 16 July 2024 at 15:15. |
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
CD32 Reset button/signal inverted ?!? | altcomputing | support.Hardware | 2 | 16 December 2021 09:53 |
TF328 RGB weird signal on amiga CD32 | leeuwtje | Hardware mods | 3 | 16 November 2021 00:26 |
A600 - No clock signal for Composite encoder | psoma | support.Hardware | 0 | 27 March 2021 11:51 |
Fuzzy picture on CD32. Bad signal? | Frimann | support.Hardware | 12 | 04 December 2011 16:24 |
A1200 no Composite or RF signal | paul773car | support.Hardware | 8 | 20 December 2009 23:49 |
|
|