Indivision MK3 A4000D

EverythingIT · 30 December 2021, 08:26

Need some help.

Recently purchased the Indivision MKIII for my A4K. I cannot plug the adapter on the CIA chips as my board has them in sockets. But I cannot seem to get DblPal No Flicker working on the Indivision. Has anyone else been able to get this mode going?

Thanks

Jope · 30 December 2021, 10:03

I don't have an Indi mk3, but here's a counter question: The indivision does the doubling and flicker fixing for you already, is there something that dblpal no flicker does for you that indivision does not?

EverythingIT · 30 December 2021, 13:25

In interlaced mode, the screen has artefacts. Just like the flicker fixer built into the A3000. DblPal No Flicker doesn't have the same artefacts.

Jope · 30 December 2021, 16:38

Do you mean the combing effect on horizontal movement?

EverythingIT · 30 December 2021, 23:44

That's it. Yes.

Jope · 31 December 2021, 07:56

Ok, in that case I get it.

The config tool is complicated, but there is a logic to it. Have you read this documentation?

http://wiki.icomp.de/wiki/Indivision_AGA_MK3/doc

How does your configuration look currently, can you take screenshots?

EverythingIT · 31 December 2021, 08:40

It is very confusing. I've managed to increase quality by increasing what resolution the MKIII outputs. Default was 800x600. I've increased it to 1280x1024 and it looks so much sharper. I'll post some pics up of my config tomorrow..

Thanks

Jope · 31 December 2021, 10:19

If you select a VGA resolution the same as your panel's native resolution, it will give you the best results with regards to sharpness.

The devil is in the refresh rates, if you can't enable vsync, you will get stutters.

EverythingIT · 02 January 2022, 00:00

After mucking around for a while. I've managed to get workbench running in 800x600. Looks awesome. Yes the config tool looks complicated. Once I got my head around it. Every screen mode looks crisp and clear now. Thank you.

30 December 2021, 08:26	#1
EverythingIT Registered User Join Date: Dec 2021 Location: Sydney Posts: 6	Indivision MK3 A4000D Need some help. Recently purchased the Indivision MKIII for my A4K. I cannot plug the adapter on the CIA chips as my board has them in sockets. But I cannot seem to get DblPal No Flicker working on the Indivision. Has anyone else been able to get this mode going? Thanks

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Indivision AGA MK3 - A Guide	AmigaLee	support.Hardware	30	23 September 2023 16:47
Indivision MK3 - Cooling	Lamaman71	Hardware mods	3	29 March 2022 15:05
FS: Indivision AGA MK3	BanisterDK	MarketPlace	11	03 January 2022 17:16
Indivision AGA MK3	Genssy	support.Hardware	27	26 April 2021 22:06
Looking for a full guide for Indivision AGA mk3	BanisterDK	support.Hardware	0	17 November 2020 21:08

30 December 2021, 10:03	#2
Jope - Join Date: Jul 2003 Location: Helsinki / Finland Age: 43 Posts: 9,861	I don't have an Indi mk3, but here's a counter question: The indivision does the doubling and flicker fixing for you already, is there something that dblpal no flicker does for you that indivision does not?

30 December 2021, 13:25	#3
EverythingIT Registered User Join Date: Dec 2021 Location: Sydney Posts: 6	In interlaced mode, the screen has artefacts. Just like the flicker fixer built into the A3000. DblPal No Flicker doesn't have the same artefacts.

30 December 2021, 16:38	#4
Jope - Join Date: Jul 2003 Location: Helsinki / Finland Age: 43 Posts: 9,861	Do you mean the combing effect on horizontal movement?

30 December 2021, 23:44	#5
EverythingIT Registered User Join Date: Dec 2021 Location: Sydney Posts: 6	That's it. Yes.

31 December 2021, 07:56	#6
Jope - Join Date: Jul 2003 Location: Helsinki / Finland Age: 43 Posts: 9,861	Ok, in that case I get it. The config tool is complicated, but there is a logic to it. Have you read this documentation? http://wiki.icomp.de/wiki/Indivision_AGA_MK3/doc How does your configuration look currently, can you take screenshots?

31 December 2021, 08:40	#7
EverythingIT Registered User Join Date: Dec 2021 Location: Sydney Posts: 6	It is very confusing. I've managed to increase quality by increasing what resolution the MKIII outputs. Default was 800x600. I've increased it to 1280x1024 and it looks so much sharper. I'll post some pics up of my config tomorrow.. Thanks

31 December 2021, 10:19	#8
Jope - Join Date: Jul 2003 Location: Helsinki / Finland Age: 43 Posts: 9,861	If you select a VGA resolution the same as your panel's native resolution, it will give you the best results with regards to sharpness. The devil is in the refresh rates, if you can't enable vsync, you will get stutters.

02 January 2022, 00:00	#9
EverythingIT Registered User Join Date: Dec 2021 Location: Sydney Posts: 6	After mucking around for a while. I've managed to get workbench running in 800x600. Looks awesome. Yes the config tool looks complicated. Once I got my head around it. Every screen mode looks crisp and clear now. Thank you.

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)