A1200 1D.4 not booting with CF/HDD - Page 2

JackTheKnife · 09 November 2022, 23:10

Quote:

Originally Posted by supaduper

Like I said just check the IDE signal is generated on pin 13 on Gayle on boot up

OK. Can you tell me where I should connect the power on the board? Also, I assume that should be set as TTL + PULSE?

supaduper · 10 November 2022, 06:14

Just use power from the four pin floppy connector, yes TTL

Kin Hell · 12 November 2022, 07:25

Quote:

Originally Posted by JackTheKnife

That sounds like I'm screwed with that board... Which exactly? Fixable or do ReAmiga transplating from that board?

Re-Amiga could save hours of wasted time investigating.

JackTheKnife · 27 November 2022, 19:02

Quote:

Originally Posted by supaduper

Like I said just check the IDE signal is generated on pin 13 on Gayle on boot up

So checked pins 13 and 14 ( _IDE_CS(1) and _IDE_CS(2)) and both are lit on high and stay on high all the time even when KS is loaded. Also kind of weird as I will suspect that Gayle will get hot in that case but is not.

I assume the light should blink or switch from HI to LO when is booting and gone when KS is fully loaded.

Any thoughts?

supaduper · 27 November 2022, 20:27

Looks like the Gayle may be faulty as the _IDE_CS(1) should send a pulse on boot up to detect if there is a Drive on the IDE port

JackTheKnife · 27 November 2022, 22:21

OK, sounds like I need to replace it. The question is to better do that on the current board or go for ReAmiga?

supaduper · 28 November 2022, 07:27

Quote:

Originally Posted by JackTheKnife

OK, sounds like I need to replace it. The question is to better do that on the current board or go for ReAmiga?

Well that board has had some damage to it so if you can do a reamiga A1200

Also get a pair of Diagrom roms so you can test the A1200 more

JackTheKnife · 03 December 2022, 23:11

Quote:

Originally Posted by supaduper

Well that board has had some damage to it so if you can do a reamiga A1200

Also get a pair of Diagrom roms so you can test the A1200 more

DiagRom test for the Gayle is stuck on that screen:

supaduper · 04 December 2022, 09:32

Yeah looks like something is not right as mine says no disk

JackTheKnife · 05 December 2022, 20:13

Quote:

Originally Posted by supaduper

Yeah looks like something is not right as mine says no disk

It looks like you have nothing connected to the IDE so based on that I have decided to take off the CF card and I have got the same as you (photo #1 below).

Then I switched the adapter to the SC card with just empty SD cards and it shows as expected (photo #2 below).

Any thoughts on that? Not enough power on for the CF card?

Kin Hell · 06 December 2022, 16:12

Re-Amiga!

+1

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
How do I stop winuae booting from hdd	Glen M	support.WinUAE	2	13 May 2017 23:35
Booting an A1200 from internal HDD.	CMcK	New to Emulation or Amiga scene	9	04 January 2012 19:56
Problem booting into workbench with HDD	SupahFlyRetard	support.Hardware	52	22 April 2009 23:23
A1200 Booting from CD	backtoskooldaze	support.Hardware	11	11 June 2002 19:24

10 November 2022, 06:14	#22
supaduper Registered User Join Date: Oct 2012 Location: Krypton Posts: 1,210	Just use power from the four pin floppy connector, yes TTL

27 November 2022, 20:27	#25
supaduper Registered User Join Date: Oct 2012 Location: Krypton Posts: 1,210	Looks like the Gayle may be faulty as the _IDE_CS(1) should send a pulse on boot up to detect if there is a Drive on the IDE port

27 November 2022, 22:21	#26
JackTheKnife Amiga Fetish Join Date: Dec 2008 Location: Downstate NY Age: 49 Posts: 267	OK, sounds like I need to replace it. The question is to better do that on the current board or go for ReAmiga?

04 December 2022, 09:32	#29
supaduper Registered User Join Date: Oct 2012 Location: Krypton Posts: 1,210	Yeah looks like something is not right as mine says no disk

06 December 2022, 16:12	#31
Kin Hell 0ld0r Git Join Date: Mar 2009 Location: Cornwall, UK Posts: 1,570	Re-Amiga! +1

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)