![]() |
![]() |
#1 |
Registered User
Join Date: May 2010
Location: Czech Rep
Posts: 599
|
Indivision ECS & Amiga 600 Joystick trouble
I recently bought new Indivision ECS and A603 memory expansion for my Amiga 600.
Installation went ok, and when was all completed, I started to play games. To my surprise my joystick worked with a problem. When I push UP it goes UP-LEFT, other directions work fine. But I cannot make a UP direction. After some testing I realized that it is caused by Indivision scandoubler, because when I disconnect scandoubler from the A603 expasion joystick works ok, when I give it back, problem is back. Does anyone knows solution for this? |
![]() |
![]() |
#2 |
Registered User
Join Date: Aug 2004
Location: www.amigakit.com
Posts: 2,051
|
Yes, the solution is to ensure that the Indivision ECS pins are firmly plugged into the socket holes on the A603. This is a connection problem.
|
![]() |
![]() |
#3 |
Registered User
Join Date: May 2010
Location: Czech Rep
Posts: 599
|
amigakit
![]() unfortunatelly problem is probably not the connection, scandoubler fits perfectly, I checked it very carefully. After having no success, I have tried scandoubler in my Amiga 500+, where it works fine, without any joystick problems. Maybe A603 problem? I really would like to have it working in my A600, any other idea? |
![]() |
![]() |
#4 |
Paranoid Amigoid
Join Date: Mar 2008
Location: Athens/Greece
Age: 45
Posts: 1,978
![]() |
I suggest (if you have a multimeter) to make a continuity test on every pin starting from the lower part of A603 to the upper socket part of Indivision ECS.
There is a chance one (or more) of A603 socket's female pin is kinda larger than it should (it can happen) so the Indivision isn't making a firm connection at this Pin. I had this issue with a random pin and when I found it, I fixed it and everything works just fine now |
![]() |
![]() |
#5 |
Registered User
Join Date: May 2010
Location: Czech Rep
Posts: 599
|
ok, thanks. My old multimetr can not do this, so I have to buy more advanced one later. If it may be a connection problem, this could probably help.
|
![]() |
![]() |
#6 |
Registered User
Join Date: Feb 2007
Location: Melbourne, Australia
Age: 41
Posts: 3,773
|
Simply use a low resistance setting instead. If you get 0 ohms or close to it you know you've got continuity.
|
![]() |
![]() |
#7 |
Registered User
Join Date: May 2010
Location: Czech Rep
Posts: 599
|
Now I discovered that the problem is the A603 itself. It does the problem even without scandoubler attached. With my old memory expansion everything works fine. I probably should contact Jens to ask him..
|
![]() |
![]() |
#8 |
Registered User
Join Date: Aug 2004
Location: www.amigakit.com
Posts: 2,051
|
Where did you buy the A603?
|
![]() |
![]() |
#9 |
Registered User
Join Date: May 2010
Location: Czech Rep
Posts: 599
|
I bought it last week at amigakit online shop with a few other things.
|
![]() |
![]() |
#10 |
Registered User
Join Date: Aug 2004
Location: www.amigakit.com
Posts: 2,051
|
Check to see if there are any shorts when the A603 is attached. Also ensure that good contact is being made with the edge connector of the A600 motherboard.
|
![]() |
![]() |
#11 |
Registered User
Join Date: May 2010
Location: Czech Rep
Posts: 599
|
the card looks ok, without any visible signs whick could case shorts. Also the contact with motherboard seems to be fine. I tested the card in both of my A600 computers with the same results.. I also tried to run without battery attached but this doesnt help either..
|
![]() |
![]() |
#12 |
Registered User
Join Date: Nov 2006
Location: Amigaville
Age: 46
Posts: 3,338
|
I guess this is just part and parcel of running old technology. Also, you invalidated your commodore warranty by breaking the seal!
![]() |
![]() |
![]() |
#13 |
Registered User
Join Date: May 2010
Location: Czech Rep
Posts: 599
|
Unfortunatelly problem not resolved, I have to send the A603 back to amigakit for an exchange for a fully working one.
|
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Quik The Thunder Rabbit ECS & AGA trouble | Retroplay | project.WHDLoad | 1 | 13 April 2013 22:22 |
[WTB] Indivision AGA (for CD32/4000) + Indivision ECS | Seaside | MarketPlace | 3 | 15 March 2012 22:03 |
Indivision ECS problem with CRT&PSU? | jimbob | support.Hardware | 13 | 16 November 2011 20:23 |
Amiga 600 joystick problem | entireweb | New to Emulation or Amiga scene | 3 | 05 October 2011 17:27 |
Trading my Indivision AGA for an Indivision ECS | 8bitbubsy | Swapshop | 3 | 11 May 2011 23:02 |
|
|