21 April 2020, 16:18 | #1 |
Registered User
Join Date: Mar 2020
Location: Istanbul/Turkey
Posts: 6
|
How to set AGA MK2CR?
Hi guys, I have Asus VW193D widesreen monitor. Monitor using 1440x900 resolution. I’m using hans’s configuration 1280x1024 but noise and vibration on Workbench screen. I wrote Indivision forum they said make a conf. 1440x900 and use it. How can I make? Someone help me?
|
22 April 2020, 13:53 | #2 |
Registered User
Join Date: Mar 2020
Location: Istanbul/Turkey
Posts: 6
|
Someone can help me?
|
22 April 2020, 14:45 | #3 |
Registered User
Join Date: Dec 2017
Location: Sassari/Italy
Posts: 871
|
Hi there and welcome on board... have you installed the Indivision config tool, the cores and the latest executable (v1.5)? First of all you should use a monitor driver like Highgfx, or extreme or DBLPAL, etc. You can find the drivers on aminet and put them on your devs:monitors directory.
Once you have done all I wrote above, restart your Amiga and open the Indivision config tool that you can find in your prefs: folder it and set your display with the right monitor and resolution. Here you can find the config tools (v1.1) and the update(v1.1). Hope this helps, ciao! |
22 April 2020, 15:24 | #4 | |
Registered User
Join Date: Mar 2020
Location: Istanbul/Turkey
Posts: 6
|
Quote:
|
|
22 April 2020, 16:08 | #5 |
Registered User
Join Date: Dec 2017
Location: Sassari/Italy
Posts: 871
|
I've just put on "the zone!" an archive with many configuration files for the Indivision AGA MK2cr.
I use the one called Indivision.conf that works well with my monitor (a 23" HP monitor). You could try to load a configuration file from the Indivision conf tool in prefs: and once loaded you should test a few configuration (e.g. PALHiRes 1024x768, Highgfx 720x576 that is the one I use or 640x480, etc...). You can also try 1440x900 with the Extreme monitor but even if it could work I'm pretty sure that it will use a lot of Chip RAM and that's not a good idea in my opinion. Having a RTG card (a Radeon 9200) I use the Indivision only for the games while I use the RTG card for the desktop so I'm not sure about what would be better in your case but only trying you will be able to find the right resolution for your Workbench and for games. Good luck! UPDATE: Once you have tested and saved the right configuration in the Indivision conf tool you have to open prefs:Screenmodes and select the monitor you want to use (use the test button before saving). A restart is usually suggested when you try a new configuration. You MUST be careful when you save a configuration in screenmode because if you save a wrong configuration you won't be able to access the WB anymore. In that case you'll have to boot without startup-sequence (or using the WB floppy disk) and remove the screenmode.prefs file in "ENV:sys/" in order to be able to access the WB again. Last edited by jurassicman; 22 April 2020 at 19:04. |
23 April 2020, 02:00 | #6 |
Registered User
Join Date: Mar 2020
Location: Istanbul/Turkey
Posts: 6
|
Ahh thanks mate I'm trying now
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Indivision AGA MK2cr - Out of sync - Please help! | jurassicman | support.Hardware | 14 | 26 January 2019 20:10 |
Indivision AGA MK2cr and animation | bitter | support.Hardware | 4 | 03 December 2018 07:08 |
Indivision AGA MK2cr? | Pheonix | MarketPlace | 4 | 12 February 2017 10:28 |
Indivision AGA MK2cr | Kickassempress | MarketPlace | 3 | 24 August 2015 01:05 |
Indivision 1200 AGA MK2cr | Seblington | support.Hardware | 11 | 25 June 2014 11:14 |
|
|