![]() |
![]() |
#1 |
Junior Member
|
A4000 Ide
Having just replaced the knackered motherboard in my A4000 - im wondering about the onboard IDE. I know about the sizing problem and have sourced a Liteon CDRW which is about 7inches long...(the DVDRW is the same size too!)
The onboard IDE interface, will it support the drive? If not what should I be looking for?. Also I see there are some PC ISA(16bit) slots on the daughter board, could I fit a 16bit ISA NIC into the slot and would it work??. |
![]() |
![]() |
#2 | ||
Registered User
Join Date: Jan 2002
Location: Germany
Posts: 7,035
|
Quote:
Quote:
|
||
![]() |
![]() |
#3 |
(Amigas && Amigos)++
Join Date: Sep 2005
Location: Anrea
Posts: 999
|
I have a Liteon DVDRW, bought for its small size! It works (at least read-only, have not yet got up to writing yet) with OS3.9. But am sure it will write also CDs with OS3.9 drivers as they are ATAPI compatible.
|
![]() |
![]() |
#4 |
.
Join Date: Oct 2004
Location: Ioannina/Greece
Posts: 5,040
|
isn't there a way with specific ISA NIC and a bridgeboard to make the NIC available on the amiga??? I think I have read it somewhere, didn't pay much attention though, neither do I know how good is this...
|
![]() |
![]() |
#5 |
Junior Member
|
Calgor - I was thinking of using os 3.5 to start off with. I am reluctant atm because I have just swapped the motherboard over and the A4K when cold booted doesnt pick up the HDD untill three soft resets later.
Anyone got any ideas on this? |
![]() |
![]() |
#6 |
Registered User
Join Date: Jan 2002
Location: Germany
Posts: 7,035
|
Does it have Kick 3.0 or 3.1 ? With 3.0 this is normal, it's just too quick for the HDD to initialise. Although it should boot at the first soft reset.
|
![]() |
![]() |
#7 | |
Thalion Webshrine
Join Date: Jan 2004
Location: Oxford
Posts: 14,478
|
Quote:
I bet you could get a 286 Bridgeboard and an ISA network card cheaper than a Zorro II network card. |
|
![]() |
![]() |
#8 | |
Registered User
Join Date: Jul 2003
Location: Budapest / Hungary
Posts: 73
|
Quote:
It uses a small MS-DOS program, constantly running on the Bridgeboard's emulated PC, to relay Ethernet data frames between the PC and the Amiga side. Therefore its performance is quite limited, and its stability is somewhat questionable, but there are Amiga owners who claim that it works for them ![]() |
|
![]() |
![]() |
#9 |
Junior Member
|
Thomas : It's 3.0 but I swapped the previous motherboard didnt have this problem!.
![]() |
![]() |
![]() |
#10 |
Registered User
Join Date: Jan 2002
Location: Germany
Posts: 7,035
|
Get some 3.1 chips. You need them for OS 3.5 anyway.
|
![]() |
![]() |
#11 |
Junior Member
|
I've just order some 3.1 chips from Italy. The O'S 3.5 on ebay seem alittle pricey! (or is it me!).
![]() |
![]() |
![]() |
#12 |
Junior Member
|
Ok Added the 3.1Roms and an A3200/A3400 with FPU! No probs so far with those parts, I also added the CDRW. Checked the drives list (holding down the mouse buttons on boot) and cannot see the CDRW at all. Am I missing something here??? should'nt it even list the drive there?.
![]() ![]() Also upgraded the OS from 3.0 to 3.1 |
![]() |
![]() |
#13 |
Registered User
Join Date: Jan 2002
Location: Germany
Posts: 7,035
|
CD drives are not recognised automatically, you have to create a mount list (see CD0 in Storage/DosDrivers for an example).
But even worse, Kickstart 3.1 and below does not recognise CD drives at all, even not with a mount list. You need an additional ATAPI driver. OS 3.5 comes with an updated IDE driver which recognises ATAPI drives, but reading the driver from CD without already having it installed is not possible ![]() A temporary solution is to install IDEfix97 demo from Aminet, then install OS3.5 and finally uninstall IDEfix. When the OS 3.5 installer asks you if you use IDEfix, reply with no. |
![]() |
![]() |
#14 |
Junior Member
|
Thanks Thomas!
![]() I was looking all over the net for a the said O.S software... ![]() ![]() ![]() |
![]() |
![]() |
#15 |
Junior Member
|
![]() HELP! update ! I have unpacked and installed idefix97 ... under the find devices - atapi - doesnt show any cdrom drive! I think I may have wired it up incorrectly. Any ideas? Last edited by Heavyweight7t6; 04 April 2006 at 17:02. |
![]() |
![]() |
#16 |
Posts: n/a
|
Check connection again
Check right Master/Slave jumpers On find devices try to select scsi.device or try another one I used it some years ago and fint out the right way after experimentations Hope this help ciao |
![]() |
#17 |
Junior Member
|
Ok ive connected up a maxtor 6.4gig and installed 3.1 onto that. How do I increase the size of the partition?. I understand 3.1 doesnt support partitions? or drives larger than 4gb - but shouldnt I have at least gotten to set size of the HD0 (workbench) and HD1 (work) before it installed 3.1?.
![]() |
![]() |
![]() |
#18 |
Registered User
Join Date: Jan 2002
Location: Germany
Posts: 7,035
|
You first create an OS3.9 emergency disk with your old setup, then you connect the new HDD and boot from the emergency disk. This way you don't have to bother with 3.1 again.
|
![]() |
![]() |
#19 |
Junior Member
|
![]() ![]() ![]() |
![]() |
![]() |
#20 |
Posts: n/a
|
Watch in:
SYS:/Prefs/env-archive/sys/screenmode.prefs or RAM:ENV/sys/screenmode.prefs |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
A4000 and IDE CD-ROM | 8bitbubsy | support.Hardware | 15 | 14 December 2011 18:00 |
A4000 IDE just died | T_hairy_bootson | support.Hardware | 14 | 05 August 2008 04:41 |
A4000 IDE Suggestions | Olecranon | support.Hardware | 13 | 25 March 2007 01:07 |
IDE CD-Burner on a4000 | th4t1guy | support.Hardware | 13 | 03 February 2006 03:29 |
IDE cd-burner for A4000 | th4t1guy | support.Hardware | 6 | 19 January 2003 19:28 |
|
|