28 September 2018, 09:13 | #41 |
Registered User
Join Date: Jun 2015
Location: UK
Posts: 472
|
Just waiting on some fresh components before I make a start
|
13 October 2018, 21:51 | #42 |
Registered User
Join Date: Mar 2015
Location: Karlstad / Sweden
Age: 52
Posts: 1,211
|
http://www.hertell.nu/webfiles/ReAmiga1200Rev12.zip
Rev 1.2: At composite 0ohm jumpers. R62 NTSC Location was connected to ground and should ACTUALLT be connected to RGB port (23pin) pin 15. no idea why this fuckup was. Corrected here.. so earlier versions of board and if you want composite/svideo in NTSC middle pad of R62 shold be connected to RGB Pin 15 instead of a jumper. PAL Is not affected IF using a VideoDAC that requires a Zenerdiode, I have now connected the R215 Correctly (was wrong on older versions not connected to +5V. so you must put a 1K resistor here if that DAC is used. on older rev. you need to connect the 1K resistor on RIGHT pad of C215 and to +5V (like top pin of D233A) Added Kickstartswitch functionality,. if you are using 27C800 proms. you can program one bank with one kickstart and the other bank with another. if R6A (bottom side of board) is set to ENA. the jumper can select the active bank. High/low with moving a jumper or a switch. (or a pic controller of your choise) if R6A is set to DIS, the A18 signal is handled as on any Amiga. to make some kind of PIC for this controlled by joystick fire or mouse left. FIR0 and FIR1 have been equipped with a TH hole for soldering a wire there. On older rev. you needed to do a slight solderblob at the pads close to U10 (between it and the FPU location) this is now a trace. Trace is visible so if you need another "strange" budgie configuration, just cut that trace and do your stuff. |
20 October 2018, 13:26 | #43 |
Registered User
Join Date: Jan 2004
Location: Yorkshire
Posts: 746
|
Have you had any feedback about your clone PCB yet?
|
20 October 2018, 17:16 | #44 |
Registered User
Join Date: Mar 2015
Location: Karlstad / Sweden
Age: 52
Posts: 1,211
|
well I still have to see someoe who soldered their board but yes I get alot of positive comments..
and well maybe 1 or 2 that say "Better to repair the existing board" |
20 October 2018, 18:19 | #45 |
Registered User
Join Date: Jan 2004
Location: Yorkshire
Posts: 746
|
Alright, I just wondered if you'd had anyone confirm that they work as I saw some on Ebay.
|
20 October 2018, 19:01 | #46 |
Registered User
Join Date: Sep 2013
Location: Beeston, Nottinghamshire, UK
Posts: 240
|
I was wondering if you'd seen this Chucky http://www.amigaclub.be/projects/amiga1200plus
I wonder why he moved the ram onto a daughter board? |
20 October 2018, 23:53 | #47 |
Registered User
Join Date: Mar 2015
Location: Karlstad / Sweden
Age: 52
Posts: 1,211
|
yes. I have some talks with him.
daughterboard.. well. devboard so.. I should also do that |
21 October 2018, 00:34 | #48 | |
Ex nihilo nihil
Join Date: Oct 2017
Location: CH
Posts: 5,065
|
Quote:
Beautiful work ! |
|
23 October 2018, 20:16 | #49 |
Registered User
Join Date: Mar 2015
Location: Karlstad / Sweden
Age: 52
Posts: 1,211
|
Added an important note to my post about ReAmiga 1200:
If you are moving from a 2B board, first of all. you need new memorymodules. BUT you also need to reprogram the GAL. you need to have the 1D.x code for XU9 location not the XU1 location GAL (same physical place but different name) code is in the R1200 archive. http://wordpress.hertell.nu/?p=618 |
30 November 2018, 08:44 | #51 |
Registered User
Join Date: Mar 2015
Location: Karlstad / Sweden
Age: 52
Posts: 1,211
|
As I did this as a replacement pcb to move components from a bad 1200 to this. I have not really checked that out.
|
30 November 2018, 19:57 | #52 |
Registered User
Join Date: Jan 2004
Location: Yorkshire
Posts: 746
|
Ah ok no worries. It's just your latest article says you are using NOS parts so I wondered what you were using.
Does anyone know any suitable substitutes for the originals? All I can find about the original ones are this. TDK ZBF503AR-00TA? It appears the boards used either a single coil or 2 small/2 large ferrite beads but you used 4 of the same size in your article? I suppose that's the same as the single coil. Last edited by Mick; 03 December 2018 at 23:57. |
25 December 2018, 22:44 | #53 |
Registered User
Join Date: Mar 2015
Location: Karlstad / Sweden
Age: 52
Posts: 1,211
|
|
26 December 2018, 22:12 | #54 |
Registered User
Join Date: Mar 2015
Location: Karlstad / Sweden
Age: 52
Posts: 1,211
|
Did a Build-guide for the ReAmiga:
http://wordpress.hertell.nu/?p=712 http://wordpress.hertell.nu/?p=735 http://wordpress.hertell.nu/?p=750 http://wordpress.hertell.nu/?p=781 |
23 February 2019, 11:29 | #55 | |
Registered User
Join Date: Feb 2019
Location: North East, UK
Posts: 10
|
Quote:
I've just came across this thread and your website, I'd like to say a huge thanks for the work you've done, there's a lot for me to read through, I really appreciate how detailed and well explained your documentation is. Thanks Casper |
|
25 February 2019, 21:08 | #56 | |
Registered User
Join Date: Feb 2015
Location: Sweden
Age: 50
Posts: 2,988
|
Quote:
Man, that Amiga Reloaded from IC sure looks less and less likely. |
|
25 February 2019, 21:18 | #57 |
Registered User
Join Date: Mar 2015
Location: Karlstad / Sweden
Age: 52
Posts: 1,211
|
Amiga 1200plus..
let me say like this: www.amiga34.de -> Amiga34 -> Aussteller point 10. and go figure.. |
14 August 2019, 22:14 | #58 |
Registered User
Join Date: Mar 2015
Location: Karlstad / Sweden
Age: 52
Posts: 1,211
|
Rev 1.4 – 74LS166 Pin 6 and 8 should be connected to Ground!
Also made changes: Moved some traces being close to edge and vias, some boardhouses had issues with this. Added headers close to 0Ohm resistors for audio, so you can skip the 0Ohn resisors and do own “mixing” if wanted. Moved onboard leds some, so they will not short to a diskdrive. Also added headers for leds if mounted in a Tower. At powerconnector, added pads for a ferritebead, so if using a round powerconnector the N/C pin can be used for ground. (NOT for use on square connector) At A500 keyboard connector, exluded the extra HDD signal for the key. if wanted, you add a 1Ohm resistor at back to enable function. Removed 3 0Ohm resistors at alice. (made them onboard instead) http://www.hertell.nu/webfiles/ReAmiga1200Rev14.zip |
15 August 2019, 13:01 | #59 |
Registered User
Join Date: Sep 2013
Location: Beeston, Nottinghamshire, UK
Posts: 240
|
Nice work Chucky, good to see you still working on it
|
16 August 2019, 15:43 | #60 |
Registered User
Join Date: Dec 2011
Location: Poland
Posts: 166
|
Good to see progress.
But now I do not know if I should assembly my Re-Amiga 1200 v1.2, or wait for newer revisions |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Amiga 1200 REV does it matter | XsamX1987 | support.Hardware | 9 | 17 February 2017 07:10 |
Amiga 1200 PAL Motherboard rev 1D.4 | amigo-mexicano | MarketPlace | 1 | 30 March 2014 23:27 |
Amiga 1200 Rev 1D.1 RGB problem | arttu80 | support.Hardware | 9 | 17 February 2013 16:12 |
AMIGA 1200 rev. 1B upgrading | wallmaker84 | Hardware mods | 23 | 30 April 2011 09:17 |
|
|