23 March 2021, 09:35 | #4621 |
Semi-Retired
Join Date: Mar 2012
Location: Leiden / The Netherlands
Posts: 2,039
|
Jbenam: Hold on... You said it didn't work with the old 17.13 version.
|
23 March 2021, 09:37 | #4622 |
Semi-Retired
Join Date: Mar 2012
Location: Leiden / The Netherlands
Posts: 2,039
|
Grelbfarlk: also the same question: can you place the cards that the voodoo is first regarding addresses?
|
23 March 2021, 09:56 | #4623 | |
Italian Amiga Zealot
Join Date: Jan 2009
Location: Italy
Age: 36
Posts: 1,913
|
Quote:
I was referring to the fact that grelbfarlk's config (which I assume was working with 17.13) gets the same error as mine does with 17.14 beta. Which apparently means that something broke when it comes to M1/K1 support. At least that's my assumption. Should I keep trying with 17.14 at this point, or should I just go back to 17.13 while I test other power supplies? |
|
23 March 2021, 14:22 | #4624 |
Semi-Retired
Join Date: Mar 2012
Location: Leiden / The Netherlands
Posts: 2,039
|
17.13 for now. I have to find the error in 17.14.
|
23 March 2021, 21:02 | #4625 |
Semi-Retired
Join Date: Mar 2012
Location: Leiden / The Netherlands
Posts: 2,039
|
Please give me the output using the following attached library.
Thanks. |
23 March 2021, 21:46 | #4626 | |
Registered User
Join Date: Dec 2015
Location: USA
Posts: 2,958
|
Quote:
Code:
Sashimi installed ([Ctrl]+C or "Break 8" to remove) Started Library Init routine Version: $VER: powerpc.library 17.14 beta (23.03.21) Detected supported Elbox Mediator PCI bridge Opening of support libraries completed 3DFX card detected, Gfx address at 64000000, config address at 62000000 Size of Gfx card in PCI memory is 03FFFFF0 Calculated from FE000008 Detected Killer M1/K1 PPC PCI card Setting up 64MB of PPC memory at 68000000 Setting up PPC card config base at 60400000 Setting up VGA PCI window at C4000000 located from 64000000 with size 800FE000 Setting up VGA config block for 3DFX Voodoo located at 62000000 Waiting on PPC card to respond Accessible PPC memory set up with header at 68410000 Inserted PPC memory into Exec memory list Library base set up at 6BFF6CB0 Copied PPC kernel code into place Gort 68K interrupt now running at 093A1B8C MasterControl now running at 09436A08 Completed adding various patches to Exec library Zen support interrupt now running at 68410024 Started Kryten PPC cleanup task Opened ppc.library emulator for PowerUP support Sashimi removed. |
|
23 March 2021, 22:21 | #4627 |
Semi-Retired
Join Date: Mar 2012
Location: Leiden / The Netherlands
Posts: 2,039
|
But does VoxelSpace and Warp3D work?
|
23 March 2021, 22:51 | #4628 |
Registered User
Join Date: Dec 2015
Location: USA
Posts: 2,958
|
Warp3D yes, I ran a GLQuake timedemo, 37FPS@640x480. Voxelspace works. Tested a couple other things like ScummVM2, Dgen, Prboom@640x480 is only getting 15.1FPS which maybe that's right for K1. Ragnarok gets about 59FPS. I guess it's right, Adoom@640x480 gets 19.22FPS.
Last edited by grelbfarlk; 23 March 2021 at 23:03. |
23 March 2021, 23:48 | #4629 |
Semi-Retired
Join Date: Mar 2012
Location: Leiden / The Netherlands
Posts: 2,039
|
OK thanks. Good to hear.
|
24 March 2021, 00:44 | #4630 |
Registered User
Join Date: Dec 2015
Location: USA
Posts: 2,958
|
The 600MHz Rapture is working now too with this version. Prboom@640x480 30.1FPS. GLQuake 640x480 43FPS. Quake2 demo1 640x480 58.4FPS. Adoom 640x480 33.42 FPS.
Asm version not working, tested back to build 381. Just says could not allocate DMA memory space machines. Last edited by grelbfarlk; 24 March 2021 at 03:37. |
24 March 2021, 14:03 | #4631 |
Registered User
Join Date: Dec 2017
Location: Rzeszów
Posts: 404
|
|
24 March 2021, 23:28 | #4632 |
Italian Amiga Zealot
Join Date: Jan 2009
Location: Italy
Age: 36
Posts: 1,913
|
Thanks for the fix. I've finally been able to test it.
The new library allocates memory then it burns down in a sea of errors. Sadly I can't save anything since the system completely freezes. I get a very large dump in MuForce around the "Accessible PPC memory set up with header at 68410000". Then another one at the end (around "Zen support..."). I think I am gonna get another voltage regulator - I trust my A4000's power supply (5V is literally a perfect 5.0V, even when under load) but I am not sure I can say the same of the power regulator I am using (AIC 1084), which was salvaged from an Ethernet PCI card I had laying around. I have also tried with an ATX power supply, things didn't seem to improve. I still want to test with a new power regulator (this time a LM1085 as in the wiki) just to be sure. |
24 March 2021, 23:40 | #4633 | |
Registered User
Join Date: Dec 2015
Location: USA
Posts: 2,958
|
Quote:
|
|
25 March 2021, 00:02 | #4634 | |
Italian Amiga Zealot
Join Date: Jan 2009
Location: Italy
Age: 36
Posts: 1,913
|
Quote:
The AIC1084 literally gets super hot which definitely doesn't make me comfortable (it even partially melted one of my hook probes!), so I thought I could test one of these nifty thingmabobs. I could also crank it up a bit and see if it helps... Will report back tomorrow |
|
25 March 2021, 00:09 | #4635 |
Registered User
Join Date: Dec 2015
Location: USA
Posts: 2,958
|
Oh good, we haven't had a good fire around here in ages!
|
25 March 2021, 00:27 | #4636 | |
Semi-Retired
Join Date: Mar 2012
Location: Leiden / The Netherlands
Posts: 2,039
|
Quote:
EDIT: Nevermind. I see an updated MuScan from last week... Still, MuForce tells me something is wrong M68K side. |
|
25 March 2021, 08:44 | #4637 | |
Italian Amiga Zealot
Join Date: Jan 2009
Location: Italy
Age: 36
Posts: 1,913
|
Quote:
I have an A3640 right now. I've also got a 040-to-060 adapter I could build, if needed, and test everything with a 060. EDIT: The el cheapo buck regulators I bought were a massive failure as it wasn't humanly possible to set them to 3.3V. I ordered another kind. Meanwhile I am testing the AIC1084 and it actually produces a very stable 3.3V. I dunno, maybe it isn't a power issue after all... EDIT2: I have tested with another 1084 I had around (it came with the 040-to-060 kit) and same issues. I think we can safely exclude the matter of power. I will now build the adapter and try with a 060... Last edited by jbenam; 25 March 2021 at 19:09. |
|
25 March 2021, 20:06 | #4638 |
Registered User
Join Date: Dec 2015
Location: USA
Posts: 2,958
|
PCI termination or slot order then? Have you tried an 8029 or 8139 NIC in the top slot?
|
25 March 2021, 20:30 | #4639 |
Italian Amiga Zealot
Join Date: Jan 2009
Location: Italy
Age: 36
Posts: 1,913
|
Forgot to say I have tested with three different 040s, so it's not a CPU issue.
Pretty sure I did in the past, but right now I am trying with just the M1 and the Voodoo 3. I'll try adding it to the mix. |
25 March 2021, 20:41 | #4640 |
Guru Meditating
Join Date: Jun 2014
Location: England
Posts: 2,354
|
Ive used an A3640 accelerator in both mediator and Prometheus and it works fine with Ragnarok and apocalypse, so the 040 might not be the issue
|
Currently Active Users Viewing This Thread: 2 (0 members and 2 guests) | |
Thread Tools | |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
WANTED: PCI Sound Card VORTEX2 SuperQuard / SQ2500 or Turtlebeach SantaCruz pci card | keropi | MarketPlace | 12 | 15 March 2017 02:48 |
Wanted:Sonnet Technologies QuadDoubler 50 (Doubler 4000) | kronuz | MarketPlace | 0 | 16 June 2013 00:29 |
eBay : Sonnet Quaddoubler | alexh | MarketPlace | 3 | 07 May 2013 00:50 |
Overlay problem on GeForce 7200 | Leandro Jardim | support.WinUAE | 1 | 10 August 2010 15:50 |
Prometheus PCI & Voodoo 3 PCI GFX Card | Slayer | support.Hardware | 21 | 05 September 2006 10:57 |
|
|