Building a HDF image for PIStorm32 Lite (Mushashi)

jumpingnerd · Today, 05:32

Hello!! :-)

So I thought I would be smart and use WinUAE to build a HDF image for my Mushashi deployment on PIStorm and spent a long time buiding a workbench 3.2.1.1 in Win-UAE and it works wonderfully.

Copied it to my PIstorm over SCP and it Pistrom starts - but wont boot from this this HDF.

So, after getting super annoyed over the course of a few hours as I searched for an answer - only to find that the only support PiSCSI HDF's with "it is a full drive RDSK/RDB image," ??

https://github.com/captain-amygdala/...s/amiga/piscsi

Which is the annoying bit as the HDF I made did not have this setting and looks like I need to redo it

So does anyone know of a good guide for building HDF's for Pistorm32?

Help is always good. thanks!

Andy

jumpingnerd · Today, 05:33

Yes in case some asks -
"Yes - I updated my config file for enable PISCSI and also Added the HDF file inside the config as well.

mja65 · Today, 10:42

The best guide I can give you is not to use Musashi at all. It's not been updated in quite a while and is slower and less compatible than Emu68, albeit it does not work with HDFs. Is there a particular reason you are trying to use this? If you use the disk partitions Emu68 uses then you can mount this in WinUae if needed

A guide for setting up a card for Emu68 is here:

https://michalsc.github.io/Emu68/tut...eparation.html

jumpingnerd · Today, 20:44

I can understand that - but the reason was to create my hard drives in a WinUAE then export/SCP to the card.

I have used Emu68K but having to remove the SD card each time I want to update it rather than SSH into it, is a bit of a pain.

But I will go back to this.

Quote:

Originally Posted by mja65

The best guide I can give you is not to use Musashi at all. It's not been updated in quite a while and is slower and less compatible than Emu68, albeit it does not work with HDFs. Is there a particular reason you are trying to use this? If you use the disk partitions Emu68 uses then you can mount this in WinUae if needed

A guide for setting up a card for Emu68 is here:

https://michalsc.github.io/Emu68/tut...eparation.html

Today, 05:32	#1
jumpingnerd Registered User Join Date: Jun 2024 Location: Auckland, New Zealand Posts: 5	Building a HDF image for PIStorm32 Lite (Mushashi) Hello!! :-) So I thought I would be smart and use WinUAE to build a HDF image for my Mushashi deployment on PIStorm and spent a long time buiding a workbench 3.2.1.1 in Win-UAE and it works wonderfully. Copied it to my PIstorm over SCP and it Pistrom starts - but wont boot from this this HDF. So, after getting super annoyed over the course of a few hours as I searched for an answer - only to find that the only support PiSCSI HDF's with "it is a full drive RDSK/RDB image," ?? https://github.com/captain-amygdala/...s/amiga/piscsi Which is the annoying bit as the HDF I made did not have this setting and looks like I need to redo it So does anyone know of a good guide for building HDF's for Pistorm32? Help is always good. thanks! Andy

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
PiStorm32 Lite and CF card	rabidgerry	support.AmigaOS	31	22 May 2024 21:48
PiStorm32-Lite problems	tech3475	support.Hardware	52	23 October 2023 17:49
PiStorm32 Lite for Amiga 1200 at AmigaKit.com	amigakit.com	MarketPlace	7	21 August 2023 18:54
PiStorm32-Lite RTG setup	cwa107	support.Hardware	5	10 May 2023 20:59
Pistorm32 Lite - Cheap (EU)	alexh	MarketPlace	1	20 April 2023 11:23

Today, 05:33	#2
jumpingnerd Registered User Join Date: Jun 2024 Location: Auckland, New Zealand Posts: 5	Yes in case some asks - "Yes - I updated my config file for enable PISCSI and also Added the HDF file inside the config as well.

Today, 10:42	#3
mja65 Registered User Join Date: Sep 2019 Location: Australia Posts: 43	The best guide I can give you is not to use Musashi at all. It's not been updated in quite a while and is slower and less compatible than Emu68, albeit it does not work with HDFs. Is there a particular reason you are trying to use this? If you use the disk partitions Emu68 uses then you can mount this in WinUae if needed A guide for setting up a card for Emu68 is here: https://michalsc.github.io/Emu68/tut...eparation.html

Currently Active Users Viewing This Thread: 2 (0 members and 2 guests)