![]() |
![]() |
#1 |
Utterly Lost....
Join Date: Oct 2013
Location: Glasgow
Posts: 167
|
A1200 boots to a purple screen.
I've not used my A1200 for a few months but tonight when I powered her up I was greeted by a blank purple screen.
Eeeek....wtf?? ![]() |
![]() |
![]() |
#2 |
Registered User
Join Date: Oct 2012
Location: South Burlington,VT,USA
Posts: 25
|
I found this but no purple
http://wiki.classicamiga.com/Amiga_b...r_code_colours |
![]() |
![]() |
#3 | |
HOL/FTP busy bee
Join Date: Sep 2006
Location: Germany
Age: 46
Posts: 31,966
|
http://home.arcor.de/rs69/A4k-HW3.html
Quote:
|
|
![]() |
![]() |
#4 |
Registered User
Join Date: May 2010
Location: Helsinki, Finland
Posts: 1,341
|
I assume it's getting far enough to start drawing the 2.x/3.x "insert disk" screen, but crashes or gets stuck after setting the background colour.
|
![]() |
![]() |
#5 |
Utterly Lost....
Join Date: Oct 2013
Location: Glasgow
Posts: 167
|
Anyone got any ideas what I should check?
|
![]() |
![]() |
#6 |
Registered User
Join Date: Feb 2013
Location: england
Posts: 19
|
Have you tried re-seating the rom chip's. this has cured some odd faults for me in the past.
|
![]() |
![]() |
#7 |
Registered User
Join Date: May 2010
Location: Helsinki, Finland
Posts: 1,341
|
Try re-seating the ROM chips for a start. If you haven't opened up the machine earlier, they are the two long chips situated roughly in the front middle of the motherboard.
|
![]() |
![]() |
#8 |
Utterly Lost....
Join Date: Oct 2013
Location: Glasgow
Posts: 167
|
I already tried reseating them, I even tried swapping them over.
It's a 1D4 motherboard. I have removed all peripherals, only keyboard is connected, CF-HD, floppy and accelerator are all unplugged. |
![]() |
![]() |
#9 |
Registered User
Join Date: Dec 2009
Location: Poole UK
Posts: 349
|
purple screen - defect paula, alice or most likely corroded track, dry joint
|
![]() |
![]() |
#10 |
Precious & fragile things
Join Date: Feb 2009
Location: Victoria, Australia
Posts: 1,946
|
One could assume a dry joint / ROM problem because changing the screen colour before the animation of the disk into the drive in 3.1 would be one of the early commands in Kickstart, then if an address line is intermittent it will fail to complete the full ROM load.
|
![]() |
![]() |
#11 |
Utterly Lost....
Join Date: Oct 2013
Location: Glasgow
Posts: 167
|
I've ordered a new set of Kickstart ROM's, they should arrive tomorrow.
If it is not the roms then where would be the best place to start looking for dry solder joints? I noticed that if I leave the purple screen on for about 20 seconds, I can hear a little 'pop' from the TV and the screen turns black. I have stripped the board down to nothing, not even the keyboard is connected, should I have the keyboard connected incase that gives an error aswell? |
![]() |
![]() |
#12 |
Precious & fragile things
Join Date: Feb 2009
Location: Victoria, Australia
Posts: 1,946
|
I would have suggested resoldering the ROM sockets would be the place to start, ordering new ROMs is highly unlikely to fix your problem.
|
![]() |
![]() |
#13 |
Utterly Lost....
Join Date: Oct 2013
Location: Glasgow
Posts: 167
|
I was going to upgrade the roms anyway mate, my current ones are 3.0 the new ones are 3.1
I'll reflow the roms sockets in the meantime. Thanks for your help. |
![]() |
![]() |
#14 |
Precious & fragile things
Join Date: Feb 2009
Location: Victoria, Australia
Posts: 1,946
|
Cool, nothing worse than wasting money on something that doesn't fix your problem.
|
![]() |
![]() |
#15 |
Utterly Lost....
Join Date: Oct 2013
Location: Glasgow
Posts: 167
|
I've resoldered the rom sockets but it didn't help. I fitted the upgraded roms and that didn't help either.
![]() Now when I power up the Amiga, the screen is purple for about 3 seconds then it turns black. |
![]() |
![]() |
#16 |
Utterly Lost....
Join Date: Oct 2013
Location: Glasgow
Posts: 167
|
OK, turns out I'm a fool and I didn't insert the new roms correctly, lol.
![]() The Amiga is now booting ok and loading things from the floppy. ![]() My new problem is that my internal CF HD is not being recognised, also my ACA1232 ram and cpu upgrade is not being recognised either. ![]() |
![]() |
![]() |
#17 |
Registered User
Join Date: Dec 2012
Location: Sweden
Posts: 125
|
Check your power supply voltages. And clean the expansion port (primarily this); It might have become dirty. I have found that using a eraser rubber, one that does not leave a discoloured surface when you use it on a paper, is good for gently rubbing the connection, to clean the metal enough to make contact. Then you can use a moist piece of paper just to be sure, let it dry properly, and then try again.
If that does not work, it is time to bring out the soldering station, the schematics, and starting fault finding... |
![]() |
![]() |
#18 |
Utterly Lost....
Join Date: Oct 2013
Location: Glasgow
Posts: 167
|
It turns out that whatever caused the ROM's to go bad also made my CF go bad!
Using WinUAE I've managed to reinstall WB3.1 back onto the CF and all is well again. ![]() Phew!! ps, I did clean the expansion port with a pencil eraser and it worked great. ![]() |
![]() |
![]() |
#19 |
Registered User
Join Date: Oct 2012
Location: South Burlington,VT,USA
Posts: 25
|
hey Stu232 how is the ACA1232 ram and cpu upgrade working now are you still having issues with that also. Wishing you the best
|
![]() |
![]() |
#20 |
Registered User
Join Date: Dec 2012
Location: Sweden
Posts: 125
|
|
![]() |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
![]() |
||||
Thread | Thread Starter | Forum | Replies | Last Post |
Blizzard MK-IV: MapRom enabled = purple screen after reboot | Scyphe | support.Hardware | 5 | 13 August 2013 04:33 |
Purple Overlay to screen | SteveE | support.Hardware | 2 | 12 March 2011 23:48 |
Purple Boot Screen? | Christian | support.Hardware | 12 | 26 May 2007 20:00 |
Blue startup screen instead of purple | mywetpants | support.Hardware | 4 | 20 March 2007 10:27 |
Boots to Green screen | Pacer238 | support.Hardware | 3 | 05 January 2006 08:34 |
|
|