English Amiga Board


Go Back   English Amiga Board > Search Forums

Showing results 1 to 40 of 10000
Search took 1.85 seconds.
Search: Posts Made By: Toni Wilen
Forum: support.WinUAE Today, 19:02
Replies: 221
Views: 36,055
Posted By Toni Wilen
Strange (also I noticed RTG blitter was always...

Strange (also I noticed RTG blitter was always disabled since b4.. winuae.7z updated).

Which AmigaOS version, Picasso96 version and what is that program that shows the corruption?
Forum: Hardware mods Today, 18:50
Replies: 4
Views: 152
Posted By Toni Wilen
$50 is normal result (bit 6 = $40 = Drive Ready,...

$50 is normal result (bit 6 = $40 = Drive Ready, bit 4 = $10 = Drive Seek Complete). $10 is obsolete but most devices still set it (and many old IDE drivers expect it)

Only important bits are 7...
Forum: support.WinUAE Today, 13:35
Replies: 221
Views: 36,055
Posted By Toni Wilen
Does it stop happening if you set NOBLITTER=YES...

Does it stop happening if you set NOBLITTER=YES in uaegfx.info? (I suspect b1 uaegfx updates that implement previously unsupported less common drawing operations are not fully correct)
Forum: support.WinUAE Yesterday, 19:58
Replies: 221
Views: 36,055
Posted By Toni Wilen
Does https://www.winuae.net/files/b/winuae.7z run...

Does https://www.winuae.net/files/b/winuae.7z run faster? I assume speed difference can be only seen in "real world" tests and pure CPU speed tests are mostly unchanged?

(This also has workaround...
Forum: support.WinUAE Yesterday, 17:48
Replies: 221
Views: 36,055
Posted By Toni Wilen
I meant if you run those commands manually one by...

I meant if you run those commands manually one by one: which one of them does not do anything or works incorrectly.

This is the usual way to debug: remove all possible variables until there is...
Forum: support.WinUAE Yesterday, 15:40
Replies: 221
Views: 36,055
Posted By Toni Wilen
Which parameter does not work? gfx_filter_overlay...

Which parameter does not work? gfx_filter_overlay at least works fine here.



Did you run the test at least 3 times? It can randomly change.
I can't see anything obvious. Try in GDI mode. If...
Forum: support.WinUAE Yesterday, 12:50
Replies: 221
Views: 36,055
Posted By Toni Wilen
Is that even beta related? Also not enough...

Is that even beta related? Also not enough information (D3D9, D3D11, both? Did it reset display, check the log)



Sysinfo is useless test (JIT speed won't change without host CPU/memory speed...
Forum: support.WinUAE Yesterday, 10:31
Replies: 221
Views: 36,055
Posted By Toni Wilen
I can't duplicate. Works fine here. Attach...

I can't duplicate. Works fine here. Attach config, thanks.
Forum: support.WinUAE 26 November 2022, 20:00
Replies: 221
Views: 36,055
Posted By Toni Wilen
https://download.abime.net/winuae/files/b/winuae_4...

https://download.abime.net/winuae/files/b/winuae_4990b7.7z
https://download.abime.net/winuae/files/b/winuae64_4990b7.7z

Beta 7:

- When on the fly changing floppy type from FloppyBridge drive...
Forum: support.WinUAE 26 November 2022, 15:26
Replies: 221
Views: 36,055
Posted By Toni Wilen
Fixed. This was very old bug....

Fixed. This was very old bug. ID3D11RenderTargetView was not freed in D3D11 shader support code.



Works for me. EDIT: If it happens without no filters, include exact mode and preferences...
Forum: support.WinUAE 26 November 2022, 12:27
Replies: 37
Views: 2,131
Posted By Toni Wilen
Thanks. This fix looks correct (always use...

Thanks. This fix looks correct (always use logical mode)
Forum: support.WinUAE 26 November 2022, 11:07
Replies: 221
Views: 36,055
Posted By Toni Wilen
Multipliers and others are now correctly used in...

Multipliers and others are now correctly used in interlace filter mode.

Check the log because I can't duplicate fall back to DX9 (it should be loggedf)



I assume D3D11 only? This has always...
Forum: support.WinUAE 24 November 2022, 21:19
Replies: 221
Views: 36,055
Posted By Toni Wilen
Are you 100% sure same config using 4.9.1 does...

Are you 100% sure same config using 4.9.1 does not have this glitch?
Forum: support.WinUAE 24 November 2022, 18:41
Replies: 9
Views: 267
Posted By Toni Wilen
Moved to separate thread.

Moved to separate thread.
Forum: support.WinUAE 24 November 2022, 18:17
Replies: 9
Views: 267
Posted By Toni Wilen
Does 4.9.1 work differently than latest beta? If...

Does 4.9.1 work differently than latest beta? If it does: it is on topic but it is also required to include which beta was introduced it.
Forum: support.WinUAE 24 November 2022, 17:54
Replies: 9
Views: 267
Posted By Toni Wilen
I don't think has anything to do with 4.9.9 betas...

I don't think has anything to do with 4.9.9 betas which means: wrong thread. This is not generic help thread.
Forum: support.WinUAE 23 November 2022, 20:07
Replies: 221
Views: 36,055
Posted By Toni Wilen
Fixed. Index sync was "sticky" in some...

Fixed. Index sync was "sticky" in some situations.



Direct3D 11 or D3D9 only? Or both?
Forum: support.WinUAE 19 November 2022, 19:57
Replies: 221
Views: 36,055
Posted By Toni Wilen
https://download.abime.net/winuae/files/b/winuae_4...

https://download.abime.net/winuae/files/b/winuae_4990b6.7z
https://download.abime.net/winuae/files/b/winuae64_4990b6.7z

Beta 6:

- Interlace mode filter crash fix (b5).
- Disk read DMA started...
Forum: support.WinUAE 17 November 2022, 19:07
Replies: 221
Views: 36,055
Posted By Toni Wilen
EHB + AGA weird behavior fixed.

EHB + AGA weird behavior fixed.
Forum: support.Other 17 November 2022, 09:49
Replies: 123
Views: 7,154
Posted By Toni Wilen
FMOVEM <registers> with no registers selected...

FMOVEM <registers> with no registers selected does nothing.
FMOVEM <control registers> always moves at least one register (FPIAR if nothing selected).

(FMOVEM <registers> has some CPU specific...
Forum: support.Other 16 November 2022, 22:46
Replies: 123
Views: 7,154
Posted By Toni Wilen
Did no one read what I replied few days ago? That...

Did no one read what I replied few days ago? That bug only affects 68060. (also not mentioning used config means: not enough information. It is also usually good idea to test few different configs,...
Forum: support.WinUAE 13 November 2022, 16:54
Replies: 7
Views: 866
Posted By Toni Wilen
SetFullscreenState(TRUE) failed 887A0001 ...

SetFullscreenState(TRUE) failed 887A0001

887A0001 means invalid call (usually means bad parameters). Driver probably not accepting "something". Possibly some later Windows version introduced "swap...
Forum: support.Other 13 November 2022, 10:30
Replies: 123
Views: 7,154
Posted By Toni Wilen
Fixed, thanks. If CPU was 68060 and FPU...

Fixed, thanks. If CPU was 68060 and FPU instruction's addressing mode was -(An) or (An)+ and FPU was disabled, original An was restored twice but second restore used invalid register index which...
Forum: support.WinUAE 12 November 2022, 19:59
Replies: 221
Views: 36,055
Posted By Toni Wilen
Restart can cause it because it frees everything...

Restart can cause it because it frees everything and initializes everything again, especially if config changes a lot. Unfortunately the dump only shows that some KS ROM memory was not allocated or...
Forum: support.WinUAE 12 November 2022, 19:49
Replies: 8
Views: 757
Posted By Toni Wilen
I think it was common misunderstanding because...

I think it was common misunderstanding because 68010 has same stack frame structure as 68020.

UAE also had this wrong: 68010 mode generated (and RTE accepted) frame type 2. I noticed it when doing...
Forum: support.Other 12 November 2022, 19:44
Replies: 123
Views: 7,154
Posted By Toni Wilen
JIT does not (can not and also not really worth...

JIT does not (can not and also not really worth the trouble) support correct FPU exception stack traces.

Unfortunately my cputester can't be used to test this because it needs to take over all...
Forum: support.WinUAE 12 November 2022, 17:49
Replies: 8
Views: 757
Posted By Toni Wilen
No. It is not same. 68010 does not have frame...

No. It is not same. 68010 does not have frame format 2!

Check the manual: http://www.bitsavers.org/components/motorola/68000/MC68010_68012_Data_Sheet_May85.pdf
Forum: support.WinUAE 12 November 2022, 15:40
Replies: 221
Views: 36,055
Posted By Toni Wilen
SMC can use huge amounts of host side RAM (~8...

SMC can use huge amounts of host side RAM (~8 bytes per Amiga side byte!)

Usually it is good idea to only use RAM inside first 16M to keep memory usage low. SMC really isn't meant to be used with...
Forum: support.WinUAE 12 November 2022, 15:29
Replies: 19
Views: 2,942
Posted By Toni Wilen
It was not (at least originally) meant for...

It was not (at least originally) meant for 68020+. 68000 is 16-bit only.
Forum: support.WinUAE 11 November 2022, 20:10
Replies: 221
Views: 36,055
Posted By Toni Wilen
Works for me. Are you really sure you use same...

Works for me. Are you really sure you use same config that also works in older version. (like having z3 ram or even too much z3 ram)
EDIT: nothing happens if smc state tables can't be allocated...
Forum: support.WinUAE 11 November 2022, 16:52
Replies: 8
Views: 757
Posted By Toni Wilen
Assuming $2014 is format/vector offset field:...

Assuming $2014 is format/vector offset field: 68010 uses same basic frame format as 68020 but it isn't same as 68020, 68010 can only generate exception frame types 0 and 8 (address/bus errors).
Forum: News 11 November 2022, 12:29
Replies: 477
Views: 122,225
Posted By Toni Wilen
Sounds like pfs3 working as designed. If...

Sounds like pfs3 working as designed.

If pfs3 can't do journal flush at the end of "transaction" (which happens few seconds after last write), whole disk operation gets rolled back (sort of, it is...
Forum: support.WinUAE 10 November 2022, 22:28
Replies: 221
Views: 36,055
Posted By Toni Wilen
winuae.7z should fix this, please confirm? (I...

winuae.7z should fix this, please confirm? (I didn't remember those options were "special")
Forum: support.WinUAE 10 November 2022, 22:20
Replies: 19
Views: 2,942
Posted By Toni Wilen
It works as designed. Only "more compatible"...

It works as designed. Only "more compatible" (prefetch) mode does indirect opcode memory reads, all other modes does direct access (for better performance), bypassing any memory bank redirections.
...
Forum: support.WinUAE 10 November 2022, 21:26
Replies: 7
Views: 866
Posted By Toni Wilen
Logs look fine. Are you sure correct display...

Logs look fine.

Are you sure correct display is selected in display panel? There is also no guarantee displays have same ordering in D3D9 vs D3D11 modes.
Forum: support.WinUAE 09 November 2022, 22:21
Replies: 1
Views: 263
Posted By Toni Wilen
Some recent version handles on the fly DPI...

Some recent version handles on the fly DPI changes badly (I think 4.9.x have it fixed).

You can reset UI settings by running winuae from command line with -resetgui (4.4.0+) command line...
Forum: support.WinUAE 06 November 2022, 19:33
Replies: 221
Views: 36,055
Posted By Toni Wilen
https://download.abime.net/winuae/files/b/winuae_4...

https://download.abime.net/winuae/files/b/winuae_4990b5.7z
https://download.abime.net/winuae/files/b/winuae64_4990b5.7z

Beta 5:

- If copper used last cycle in scanline and last cycle was even...
Forum: support.WinUAE 06 November 2022, 16:44
Replies: 221
Views: 36,055
Posted By Toni Wilen
Octamed was good :) Duplicated the hang. Does...

Octamed was good :) Duplicated the hang. Does https://www.winuae.net/files/b/winuae.7z fix it?
Forum: support.WinUAE 06 November 2022, 15:29
Replies: 221
Views: 36,055
Posted By Toni Wilen
But the point is that I don't get that far....

But the point is that I don't get that far. playmf output some text to CLI and then it hangs with nothing sent to serial port. CTRL+C does exit. Same with any UAE version -> some configuration is...
Forum: support.WinUAE 06 November 2022, 14:44
Replies: 2
Views: 378
Posted By Toni Wilen
It is crash caused by deallocation of A2065 while...

It is crash caused by deallocation of A2065 while slirp was reading from its on board RAM (not a new bug but it can be quite random). I'll add fix to next beta.
Showing results 1 to 40 of 10000

 
Forum Jump

All times are GMT +2. The time now is 21:30.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2022, vBulletin Solutions Inc.
Page generated in 1.18399 seconds with 10 queries