FPGA Replay Case

wizard66 · 19 March 2011, 15:48

Hi guys,

I have decided to design a housing for the FPGAArcade Replay.
Some of you maybe remember I did a few runs of minimig housings.
There will be two kit versions of cases including spacers and bolts.
The cases will be made from Plexiglas just like the minimig cases.

Versions:

1. For the FPGAArcade Replay mainboard.

2. One for the FPGAArcade Replay Including the 060 daughterboard.
This version will include a sunroof/hole for the processor so the heat sink can vent out the top op the case (only the square heat sink will be supported)

********* ********** UPDATE ********* **********

The first prototype for the FPGAARCADE is ready ;-))

This is the version for use with the FPGAARCADE mainboard only (so the mainboard without the daughterboard from Yacube)

There are two set options:
Set 1 AMI: Amiga Set Complete set including spacers and bolds Including Amiga Text and boingball logo (see picture nr.1).
Set 2 UNI: Universal set NONE logo's Complete set including spacers and bolds (see picture nr.2)

I can supply more logo's in the future but we will see.

If you are interested in one of this sets let me know I will keep a list of peoples interested.
The minimal units I have to get is 25 before the production can take place.
If The 25 units are confirmed I will e-mail ALL for payment then the production will start (I WILL DELIVER as I did in the past just look up the minimig cases thread)

Cost:
Set UNI Universal set E 28,50 shipment E 12,00
Set AMI Amiga Set E 36,00 shipment E 12,00

The case design including Yacube’s daughterboard is not begun yet because I don’t have any measurements.
I will contact MikeJ or Yaqube if there is progress in rerouting the daughterboard for the CPU placement on the new daughterboard.

***** Update 16-5-2011 *****

Okey boys and girls,

After some e-mail swapping between MikeJ and me there are some changes here.
MikeJ has ask me if I want to use his original fpgaarcade logo on the case's (let me think ;-) YEEEEEEEEEEEES !!!! )
So here is a update from the case on drawing, the quality of the product will be the same as the pictures on page one, so only the engraving will change.

The picture is for the amiga version the Universal version is the same like this without the amiga logo, DUhu..

The 060 daughterboard version will also include this logo and some other stuff ;-) Daughterboard version pending….

*** LIST of peoples who want a Set***

1. 1 x Set AMI Maffoo @ Amiga.org
2. 1 x Set AMI Darrin @ Amiga.org
3. 1 x Set AMI gxenakis @ Minimig.net
4. Set
5. Set
6. Set
7. Set
8. Set
9. Set
10. Set
11. Set
12. Set
13. Set
14. Set
15. Set
16. Set
17. Set
18. Set
19. Set
20. Set
21. Set
22. Set
23. Set
24. Set
25. Set

I Hope you all like this version ;-)

HIRES PICTURES MEGAUPLOAD, PM me if the link is dead
http://www.megaupload.com/?d=ZOAKCUQ3

Kitty · 19 March 2011, 21:26

I'm interested ;D
Can you do a glass version as well as perspex, I would prefer glass with beveled edges ofc

I don't mind paying a little more for glass if its more costly.
So that 060 daughter board is actually a reality?
This just gets better and better I cant wait for a release. I better start saving up

wizard66 · 19 March 2011, 22:07

Quote:

Originally Posted by Kitty

I'm interested ;D
Can you do a glass version as well as perspex, I would prefer glass with beveled edges ofc

I don't mind paying a little more for glass if its more costly.
So that 060 daughter board is actually a reality?
This just gets better and better I cant wait for a release. I better start saving up

Sorry no glass versions are be made.

Kitty · 19 March 2011, 22:11

ahh ok

wizard66 · 29 March 2011, 14:00

Today I received my FPGAArcade board.
So I can start designing the cases...

mfilos · 29 March 2011, 14:51

I'm drooling already...

Share the pr0n every step of the way mate!!!
Awesome board, thanks for sharing \o/

Kitty · 29 March 2011, 18:59

can u show us screens and videos of the c64 core when u got time

wizard66 · 09 May 2011, 16:17

Today the prototype has arrived.
Now I have to measure the spacers and order the right bolds.
The Plexiglas is 3mm thick, so nice and strong.
I will display the pictures in a few day’s
Production run @ the company has to be @least 25 unit’s.
Prize will follow.

wizard66 · 11 May 2011, 08:40

The first prototype case is ready see top this page

imigger · 12 May 2011, 01:08

when can we buy 1????as in replay board

whiteb · 12 May 2011, 10:17

@Mr Wizard66

I take it the case design also accommodates the planned 060 add on board as well ?

[edit] okay sorry, I didnt see there was Model #2 for a Heat vent hole for the 060.

wizard66 · 16 May 2011, 13:22

Update 16-5-2011

Okey boys and girls,

After some e-mail swapping between MikeJ and me there are some changes here.
MikeJ has ask me if I want to use his original fpgaarcade logo on the case's (let me think ;-) YEEEEEEEEEEEES !!!! )
So here is a update from the case on drawing, the quality of the product will be the same as the pictures on page one, so only the engraving will change.

The picture is for the amiga version the Universal version is the same like this without the amiga logo, DUhu..

The 060 daughterboard version will also include this logo and some other stuff ;-) Daughterboard version pending….

ajacocks · 16 May 2011, 22:07

Great work, wizard66. When the replay+daughterboard become available, I'll definitely want a case.

- Alex

chiark · 16 May 2011, 23:51

as soon as it's clear how much the fpgaarcade, and optionally how much the 060 card will be, I'll know which version to order

digiflip · 19 May 2011, 20:12

have you pics of the daughter board version of your case yet wizard?

wizard66 · 20 May 2011, 11:54

Quote:

Originally Posted by digiflip

have you pics of the daughter board version of your case yet wizard?

No I have not.
MikeJ is rerouting the daughterboard so I dont have the specs yet.
Yacubes Daughterboard is a other version then we will have.
Be couse yacube's board don't have the double stacked connectors on his mainboard.
It will take a some time to disign a case for that but I hope to be intime for the main release date.

fgh · 11 February 2012, 09:39

Someone make a 3d model of a scaled down a600 (or a3000 to fit the daughterboard) designed to fit the replay, and we can have them 3D printed from shapeways.com.
Now that would be a suitable cabinet

19 March 2011, 15:48	#1
wizard66 FPGA Replay inside A590 Join Date: Sep 2004 Location: Spijkenisse/Netherlands Age: 46 Posts: 289	FPGA Replay Case Hi guys, I have decided to design a housing for the FPGAArcade Replay. Some of you maybe remember I did a few runs of minimig housings. There will be two kit versions of cases including spacers and bolts. The cases will be made from Plexiglas just like the minimig cases. Versions: 1. For the FPGAArcade Replay mainboard. 2. One for the FPGAArcade Replay Including the 060 daughterboard. This version will include a sunroof/hole for the processor so the heat sink can vent out the top op the case (only the square heat sink will be supported) ******* ****** UPDATE ***** ****** The first prototype for the FPGAARCADE is ready ;-)) This is the version for use with the FPGAARCADE mainboard only (so the mainboard without the daughterboard from Yacube) There are two set options: Set 1 AMI: Amiga Set Complete set including spacers and bolds Including Amiga Text and boingball logo (see picture nr.1). Set 2 UNI: Universal set NONE logo's Complete set including spacers and bolds (see picture nr.2) I can supply more logo's in the future but we will see. If you are interested in one of this sets let me know I will keep a list of peoples interested. The minimal units I have to get is 25 before the production can take place. If The 25 units are confirmed I will e-mail ALL for payment then the production will start (I WILL DELIVER as I did in the past just look up the minimig cases thread) Cost: Set UNI Universal set E 28,50 shipment E 12,00 Set AMI Amiga Set E 36,00 shipment E 12,00 The case design including Yacube’s daughterboard is not begun yet because I don’t have any measurements. I will contact MikeJ or Yaqube if there is progress in rerouting the daughterboard for the CPU placement on the new daughterboard. * Update 16-5-2011 * Okey boys and girls, After some e-mail swapping between MikeJ and me there are some changes here. MikeJ has ask me if I want to use his original fpgaarcade logo on the case's (let me think ;-) YEEEEEEEEEEEES !!!! ) So here is a update from the case on drawing, the quality of the product will be the same as the pictures on page one, so only the engraving will change. The picture is for the amiga version the Universal version is the same like this without the amiga logo, DUhu.. The 060 daughterboard version will also include this logo and some other stuff ;-) Daughterboard version pending…. * LIST of peoples who want a Set*** 1. 1 x Set AMI Maffoo @ Amiga.org 2. 1 x Set AMI Darrin @ Amiga.org 3. 1 x Set AMI gxenakis @ Minimig.net 4. Set 5. Set 6. Set 7. Set 8. Set 9. Set 10. Set 11. Set 12. Set 13. Set 14. Set 15. Set 16. Set 17. Set 18. Set 19. Set 20. Set 21. Set 22. Set 23. Set 24. Set 25. Set I Hope you all like this version ;-) HIRES PICTURES MEGAUPLOAD, PM me if the link is dead http://www.megaupload.com/?d=ZOAKCUQ3 Attached Thumbnails Last edited by wizard66; 16 May 2011 at 13:28.

19 March 2011, 22:11	#4
Kitty Stay a while,Stay Forever Join Date: Mar 2005 Location: UK London Age: 30 Posts: 1,308	ahh ok __________________ http://awesome.commodore.me http://awesome.commodore.me/forum http://twitter.com/CommodoreBlog http://www.facebook.com/pages/Commod...169766?sk=wall

29 March 2011, 14:00	#5
wizard66 FPGA Replay inside A590 Join Date: Sep 2004 Location: Spijkenisse/Netherlands Age: 46 Posts: 289	Today I received my FPGAArcade board. So I can start designing the cases... Attached Thumbnails Last edited by wizard66; 14 April 2011 at 19:29.

29 March 2011, 14:51	#6
mfilos Paranoid Amigoid Join Date: Mar 2008 Location: Athens/Greece Age: 34 Posts: 1,315	I'm drooling already... Share the pr0n every step of the way mate!!! Awesome board, thanks for sharing \o/ __________________ Visit my Amiga blog here - A4000D: 060@50/604@180, 384MB,ACard+80GB HD,SCSI Multicard Reader,DVD-RW,Grex4000 (RTG/Sound/NIC),Indivision 4000,RTG/AGA AutoSwitch,Deneb,ZorRAM - A600: 030@37.5, 64MB, A604, 16GB CF, Indivision ECS, Subway, MAS-Player (internal), Custom Audio Mixer, HxC SD+Slim floppy (internal)

09 May 2011, 16:17	#8
wizard66 FPGA Replay inside A590 Join Date: Sep 2004 Location: Spijkenisse/Netherlands Age: 46 Posts: 289	Today the prototype has arrived. Now I have to measure the spacers and order the right bolds. The Plexiglas is 3mm thick, so nice and strong. I will display the pictures in a few day’s Production run @ the company has to be @least 25 unit’s. Prize will follow. __________________ Computers: 1x FPGArcade V1.0B 1x Minimig V1.1 (Home build) 4MB + ARM Controller Last edited by wizard66; 10 May 2011 at 13:12.

19 March 2011, 21:26	#2
Kitty Stay a while,Stay Forever Join Date: Mar 2005 Location: UK London Age: 30 Posts: 1,308	I'm interested ;D Can you do a glass version as well as perspex, I would prefer glass with beveled edges ofc I don't mind paying a little more for glass if its more costly. So that 060 daughter board is actually a reality? This just gets better and better I cant wait for a release. I better start saving up __________________ http://awesome.commodore.me http://awesome.commodore.me/forum http://twitter.com/CommodoreBlog http://www.facebook.com/pages/Commod...169766?sk=wall Last edited by Kitty; 19 March 2011 at 21:31.

29 March 2011, 18:59	#7
Kitty Stay a while,Stay Forever Join Date: Mar 2005 Location: UK London Age: 30 Posts: 1,308	can u show us screens and videos of the c64 core when u got time

11 May 2011, 08:40	#9
wizard66 FPGA Replay inside A590 Join Date: Sep 2004 Location: Spijkenisse/Netherlands Age: 46 Posts: 289	The first prototype case is ready see top this page __________________ Computers: 1x FPGArcade V1.0B 1x Minimig V1.1 (Home build) 4MB + ARM Controller

12 May 2011, 01:08	#10
imigger Registered User Join Date: Apr 2011 Location: england Posts: 113	when can we buy 1????as in replay board

12 May 2011, 10:17	#11
whiteb Fanatically Amiga. Join Date: Apr 2002 Location: Melbourne, Victoria, Australia Age: 43 Posts: 1,354	@Mr Wizard66 I take it the case design also accommodates the planned 060 add on board as well ? [edit] okay sorry, I didnt see there was Model #2 for a Heat vent hole for the 060.

16 May 2011, 13:22	#12
wizard66 FPGA Replay inside A590 Join Date: Sep 2004 Location: Spijkenisse/Netherlands Age: 46 Posts: 289	Update 16-5-2011 Okey boys and girls, After some e-mail swapping between MikeJ and me there are some changes here. MikeJ has ask me if I want to use his original fpgaarcade logo on the case's (let me think ;-) YEEEEEEEEEEEES !!!! ) So here is a update from the case on drawing, the quality of the product will be the same as the pictures on page one, so only the engraving will change. The picture is for the amiga version the Universal version is the same like this without the amiga logo, DUhu.. The 060 daughterboard version will also include this logo and some other stuff ;-) Daughterboard version pending…. Attached Thumbnails __________________ Computers: 1x FPGArcade V1.0B 1x Minimig V1.1 (Home build) 4MB + ARM Controller

16 May 2011, 22:07	#13
ajacocks Registered User Join Date: Mar 2009 Location: Falls Church, Virginia, USA Posts: 57	Great work, wizard66. When the replay+daughterboard become available, I'll definitely want a case. - Alex

16 May 2011, 23:51	#14
chiark Needs a life Join Date: Jan 2008 Location: England Posts: 1,564	as soon as it's clear how much the fpgaarcade, and optionally how much the 060 card will be, I'll know which version to order

19 May 2011, 20:12	#15
digiflip Registered User Join Date: Apr 2011 Location: United Kingdom Posts: 46	have you pics of the daughter board version of your case yet wizard?

11 February 2012, 09:39	#17
fgh Registered User Join Date: Dec 2010 Location: Norway Posts: 265	Someone make a 3d model of a scaled down a600 (or a3000 to fit the daughterboard) designed to fit the replay, and we can have them 3D printed from shapeways.com. Now that would be a suitable cabinet

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
FPGA hardware status	Parsec	Amiga scene	25	07 January 2011 02:07
Amiga on a FPGA?	Narf the Mouse	Amiga scene	7	25 November 2010 23:26
Free : PCMCIA PC card FPGA devkits	alexh	MarketPlace	7	20 November 2009 10:26
c-one FPGA extender	xc8	News	9	23 November 2008 20:36
Amiga Video Toaster in FPGA just like minimeg	Pyromania	Amiga scene	18	30 November 2007 01:42