Accelerator board emulation

[McTrinsic]

O. K. give me a day or two...

[rlake]

Originally Posted by Toni Wilen

tools/showconfig output:

- without running any Derringer utilities
- after running utility that adds RAM
- after running utility that adds RAM + MAPROM enabled
- above two tests repeated with different RAM size (if you have different size SIMMs)

EDIT: if no showconfig (only 1.3), sysinfo boards and memory lists are also fine.

Got my system up and running over the break with help from the GVP emulation in FS-UAE to create a new WB 2.1 flash card. Here's the requested information, note the ROM mapping does not affect the config (would appear to match the manual in loading to RAM).

No utilities:

PROCESSOR:	CPU 68030/68882fpu/68030mmu
CUSTOM CHIPS:	ECS PAL Agnus (id=$0020), ECS Denise (id=$00fc)
VERS:	Kickstart version 37.350, Exec version 37.152, Disk version 38.36
RAM:	Node type $a, Attributes $205 (FAST), at $200000-$5fffff (4.0 meg)
	Node type $a, Attributes $303 (CHIP), at $400-$fffff (~1.0 meg)
BOARDS:
 Board + ROM (HD?) (unidentified):   Prod=2017/11($7e1/$b) (@$e90000 64K)
 RAM (unidentified):   Prod=2017/10($7e1/$a) (@$200000 4meg Mem)

Executing "d3 dram" (command output, showconfig):

D3: CSA Derringer 030 Configuration Software, Version 1.0
  CPU/FPU = 68030/68882
DRAM Configuration:
  ** SizeSimmUp returned a bitmap of $FFFF **
  ** SizeSimmDn returned a bitmap of $FFFF **
  Memory range 08000000-09FFFFFF: Passed Test.
  32MB of 32-bit DRAM memory added to system
D3.

PROCESSOR:	CPU 68030/68882fpu/68030mmu
CUSTOM CHIPS:	ECS PAL Agnus (id=$0020), ECS Denise (id=$00fc)
VERS:	Kickstart version 37.350, Exec version 37.152, Disk version 38.36
RAM:	Node type $a, Attributes $5 (FAST), at $8000010-$9ffffff (~32.0 meg)
	Node type $a, Attributes $205 (FAST), at $200000-$5fffff (4.0 meg)
	Node type $a, Attributes $303 (CHIP), at $400-$fffff (~1.0 meg)
BOARDS:
 Board + ROM (HD?) (unidentified):   Prod=2017/11($7e1/$b) (@$e90000 64K)
 RAM (unidentified):   Prod=2017/10($7e1/$a) (@$200000 4meg Mem)

Executing "d3 drom" (command output):

D3: CSA Derringer 030 Configuration Software, Version 1.0
  CPU/FPU = 68030/68882
DROM Configuration:
  512k DROM now enabled.
D3.

[McTrinsic]

Hi Toni,

similar results here.

Executed showconfig by hand.

Screenshots:
- without DRAM utility
- without DRAM utility and in 68000 mode
- with DRAM utility
- with DRAM utility and ROM feature enabled.

Do not see a difference between the last two ones.

Cheers,
McT

[McTrinsic]

Does that Info actually help??

[Toni Wilen]

Yes. It could even work just by manually adding some "CPU board" RAM, it has same address space. If software does not use some board specific hardware, too lazy to check this too soon..

[McTrinsic]

Great to hear.

For emulation purposes, personally, I could happily live without maprom feature.

Cheers,
McT