06 January 2014, 17:08 | #1 |
Bawbag.
Join Date: Mar 2008
Location: Chicago, USA
Posts: 375
|
Trouble Setting up Transcend 4GB IDE Flash Disk
Hi,
I recently bought one of these to replace the aging hard drive in my A4000 http://www.ebay.com/itm/Transcend-4G...item461404f31a HDToolBox can see the drive, and I partitioned it with the following settings. Partition name: DH0 File system: Standard File System, FFS Mask 0x7ffffffe Max Transfer 0x1fe0000 Block size 512 Size of partition: 1024MB I can install WB 3.1 on the partition just fine and reboot and run it without any issues. The problem arises after installing ASIM CDFS v3.10 which Ive used in the past with no issues. After installing it and rebooting I start getting the following errors: DH0 has a checksum error on disk block 1056187 Ive never seen this happen before - never had this issue with other drives, both CF and 3.5" in the past. How do I go about troubleshooting this error? Mark |
06 January 2014, 17:46 | #2 |
Moderator
Join Date: May 2012
Location: Stockholm / Sweden
Age: 49
Posts: 1,575
|
First of all, I would not use FFS as it will drive you mad with its validation problems. Use a filesystem that can handle an unexpected shutdown. I strongly recommend PFS3-AIO.
http://aminet.net/search?query=pfs3+aio My cheatnotes: PFS\03 = 0x50465303 Mask = 0x7ffffffe (There are 6 f’s) MaxTransfer = 0x1fe00 Blocksize = 512 PFS3\Tools\pfsformat device DH1: Name Work Quick fnsize 107 NOICONS That is a good start at least. Never played with those devices before (only IDE-CF).. |
06 January 2014, 18:53 | #3 |
Registered User
Join Date: Jan 2002
Location: Germany
Posts: 7,002
|
|
06 January 2014, 20:27 | #4 |
Bawbag.
Join Date: Mar 2008
Location: Chicago, USA
Posts: 375
|
Thomas - give me five mins and I'll try again.
FYI when I define/edit the drive type for the first time details are: Manufacturers Name: TRANSCEN Drive Name: D Drive Revision: 2011 Cylinders: 7769 Heads: 16 Blocks per Track: 63 Blocks per Cylinder: 1008 Park head where (cylinder): 7769 |
06 January 2014, 20:32 | #5 |
Bawbag.
Join Date: Mar 2008
Location: Chicago, USA
Posts: 375
|
Creating partition with
Mask: 0x7ffffffe MaxTransfer: 0x1FE00 (I hit enter after setting this to make the value stays) File System Block Size: 512 Reserved blocks at: Beginning: 2 End: 0 On the Partitioning screen Start cyl: 3 End cyl: 1044 Total Cyl: 1042 Buffers: 30 Partition size for DH0 is 512 Meg Now installing WB... |
06 January 2014, 20:50 | #6 |
Bawbag.
Join Date: Mar 2008
Location: Chicago, USA
Posts: 375
|
Ok its installed. Rebooted a couple of times to see if I can boot to Workbench on the HD without any issues.
Moving onto installing ASIMCDFS 3.10 The HD is on the same cable as the cdrom - hd is master, cdrom is slave. |
06 January 2014, 20:54 | #7 |
Bawbag.
Join Date: Mar 2008
Location: Chicago, USA
Posts: 375
|
Ah,
its during the install of ASIMCDFS while its copying files to DH0: that I get the checksum error. DH0 has a checksum error on disk block 530273. So, from a drive setup point of view, have I setup the drive correctly? I believe I have, because I've followed the instructions set out, for example setting MaxTransfer to 0x1fe00. So is this as terran points out, just FFS being flakey or could it be an issue with the drive itself? |
06 January 2014, 20:56 | #8 |
Bawbag.
Join Date: Mar 2008
Location: Chicago, USA
Posts: 375
|
And actually, after installing ASIM CDFS and rebooting, I just get the drive prompt. Its as if the drive isnt there. So, faulty drive?
|
06 January 2014, 21:09 | #9 | |
Registered User
Join Date: Jan 2002
Location: Germany
Posts: 7,002
|
Quote:
The reason for my question is that the standard AmigaOS IDE driver (called scsi.device) does not support CD drives (or ATAPI drives in general). It needs some additional software to recognise a CD drive. Because of its age this additional software might interfere with how CF cards identify themselves. The same happens with IDEfix: once the IDEfix software is active, CF cards are no longer recognised. If this happens while the OS is already running, it could well be the reason for the checksum error. Does the drive reappear if you switch the Amiga off and on again (to remove all resident modules from RAM)? |
|
06 January 2014, 21:13 | #10 |
Bawbag.
Join Date: Mar 2008
Location: Chicago, USA
Posts: 375
|
Thomas -
The installer asks which device you want to probe for devices... theres an asim_atapi.device that detects my cdrom. Switching off the A4000 completely and switching it back on, I get the insert floppy screen, no booting to HD. |
06 January 2014, 23:31 | #11 |
Registered User
Join Date: Jan 2002
Location: Germany
Posts: 7,002
|
If you insert the Install disk and run HDToolbox, are all partitions gone or is anything left? Do you have to "change drive type" or can you start creating partitions without that?
What's your hardware configuration? This DOM has a female connector which shall plug directly to the motherboard. But "asim_atapi.device" (which AFAIK is an ATAPI driver for the motherboard's IDE controller) finds your CD drive, so the drive is connected to the motherboard. Where is the DOM connected to then? Can you copy files to the DOM partition without installing AsimCDFS? Does it fail then, too? How many files (or megabytes) can you copy to the partition? Does it fail also if you make the partition smaller, for example 100 MB? Can you make a boot floppy with AsimCDFS installed so that the CD driver is active before you install the DOM? Does it fail earlier then, for example already during installation of WB? Which version of WB are we talking about? Your signature says OS 3.9. Why do you install AsimCDFS when you have CacheCDFS out of the box? If it's not OS 3.9, what if you try OS 3.9? Does it boot from your emergency disk? And does HDToolbox see the DOM when OS 3.9 has booted from CD? Can you install OS 3.9 to the DOM? |
07 January 2014, 00:07 | #12 |
Bawbag.
Join Date: Mar 2008
Location: Chicago, USA
Posts: 375
|
Hi Thomas
Im actually running 3.1 in this case. I had 3.9 installed on another drive a while back, butin this case since Im setting up a new drive decided to go with 3.1 in the first instance. I have an A4000 with an Apollo 4060 Accelerator, a specturm 24/48 card and Deneb USB card. The DOM has a female connector that is correct, but I have an adapter cable so it can connect into a regular IDE cable, so both DOM and CDROM can connect to the single IDE port on the A4000 Before installing ASIM CDFS I was able to install other programs from Floppy - Amigakits EasyADF for example without any issues. So maybe less than a MB. I havent been able to copy multiple MB's yet. When I start up with the install disk, I dont have to change drive type before creating partitions. I think the partitions are there, but I dont see them from the workbench floppy disk. Mark |
07 January 2014, 00:15 | #13 |
Professional slacker!
|
What type of IDE cable are you using?
I was setting up a CDROM on my A1200 recently with 4Way IDE device and I was using a modern rounded IDE cable, every time I installed the CDROM with IDEFix97 it trashed my DH0, I was getting SFS errors too. I changed the cable for an older style, flat grey cable and it's working like a charm since! |
07 January 2014, 05:08 | #14 |
Bawbag.
Join Date: Mar 2008
Location: Chicago, USA
Posts: 375
|
@Fitzsteve - it is an old style ide cable - I'll take some pictures of the internals of the A4000 and put them up to post. Although I wonder if its the male-male cable adapter that is causing the issue.
|
07 January 2014, 11:05 | #15 | ||
Registered User
Join Date: Jan 2002
Location: Germany
Posts: 7,002
|
Quote:
Actually I wonder why you pay so much money for a rather small DOM disk and a non-standard adapter cable when you can have a matching CF-IDE adapter plus a very large CF card for the same money. Another point: did you ever have a working OS with the Deneb drivers installed? If yes, you could have put the drivers into the Deneb's flash ROM and then could boot from an USB card reader or memory stick. No need to deal with floppies any more. Quote:
What if you hold down both mouse buttons immediately during power-on, do the partitions appear in the early startup menu? What happens if you click on "boot without startup-sequence" then? |
||
07 January 2014, 11:22 | #16 |
Professional slacker!
|
A solution could be a 4way IDE device splitter and use the CDROM on the second channel so the DOM can totally occupy the first. You might need to install IDEFix97 to activate the secondary channel though.
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
My new SSD! Transcend 4Gb IDE Flash Module | Mrs Beanbag | Hardware pics | 48 | 14 December 2012 23:05 |
4GB CF IDE HARD DISK www.amigakit.com | amigakit.com | MarketPlace | 0 | 22 September 2010 14:24 |
4gb Solid State Disk on Module (ide) | Smiley | MarketPlace | 18 | 31 January 2010 15:44 |
Vertical IDE Flash module 44Pin 4GB | NovaCoder | support.Hardware | 14 | 31 July 2008 18:58 |
Transcend 4GB IDE Flash Module? | Molcos | MarketPlace | 3 | 16 April 2008 09:07 |
|
|