Sonnet 7200 PCI programming - Page 199

grelbfarlk · 18 May 2020, 17:07

@Johnnybarker did you set:
-Harrier256MB (0 or 1): Enable if you have a Harrier based G4 card with 256MB.

@TheMrKocour
Yes due to the Spider using three IRQs, they are going to share with something. I haven't run the Sonnet in a long time but I was using the Spider with it successfully. Currently I have a Sphyder in with an Apocalypse and it basically works.

johnnybarker · 18 May 2020, 17:11

Oh, just reading the github again, looks like I may need to alter the envarc harrier =1?

I know, RTFM. In the bath now so will try later.

johnnybarker · 18 May 2020, 17:14

Thanks grelbfarlk- screen refreshed too late to read your post before I replied to myself!

Fingers crossed. I am hoping that if the RAM/soldering was dodgy then it would not work at all.

grelbfarlk · 18 May 2020, 17:43

Quote:

Originally Posted by johnnybarker

Thanks grelbfarlk- screen refreshed too late to read your post before I replied to myself!

Fingers crossed. I am hoping that if the RAM/soldering was dodgy then it would not work at all.

Yeah, that's what I've seen. So if it's working with 128MB out of 256MB it's probably fine.

johnnybarker · 18 May 2020, 19:52

Hooray it works!

Thanks again grelbfarlk for all the hard work you did in creating/testing this mod.

Now that it is working I will admit that that I did go for the cheap RAM chips off Aliexpress.

Timtheloon · 18 May 2020, 19:54

Quote:

Originally Posted by johnnybarker

Now that it is working I will admit that that I did go for the cheap RAM chips off Aliexpress.

Got a link to them I’ll get some for mine

grelbfarlk · 18 May 2020, 20:20

Quote:

Originally Posted by johnnybarker

Hooray it works!

Thanks again grelbfarlk for all the hard work you did in creating/testing this mod.

Now that it is working I will admit that that I did go for the cheap RAM chips off Aliexpress.

I mean I didn't really do any more work than you did, but I'll accept the props. Glad you got it done on the cheap as well.

johnnybarker · 18 May 2020, 21:25

Quote:

Originally Posted by Timtheloon

Got a link to them I’ll get some for mine

This is what I bought

https://www.aliexpress.com/item/3259...40fc5764SsGVd1

They appear to be even cheaper now.

I used an "Aoyue 1257 - Air Nozzle SOP Type - 11 x 21mm" with an antex hot air gun and, with plenty of flux, the chips came off quite easily.

I did actually buy a spare apocalypse card from the seller in Israel as I wasn't confident I could change the chips without bricking at least one card. I also bought enough RAM chips to do the second card. If I get time between working and home schooling I may have a bash at the second card and if successful will pass it on for what I paid for it.

Timtheloon · 18 May 2020, 21:48

Hopefully I’ve bought the right ones

johnnybarker · 18 May 2020, 22:08

Looks good.

TheMrKocour · 22 May 2020, 18:58

Hi, any news on SheepShaver or iFusion?

grelbfarlk · 22 May 2020, 19:06

Quote:

Originally Posted by TheMrKocour

Hi, any news on SheepShaver or iFusion?

No, unfortunately we need a coder with at least 6th level spell slots, and they're all busy on something else.
*Edit* And no, Six 1st level spells are not equivalent or First level working six times as hard.

Timtheloon · 25 May 2020, 10:49

Hi I noticed this issue has been closed and marked as done on the GitHub.

“Add an auto-detect routine for memory size for Apocalypse cards. #9”

Does this mean we no longer need the jumper on 128mb cards?

Hedeon · 25 May 2020, 13:01

Thats a different library. And it removes the need for the env, not the jumper
That one prevents booting of the card into its own kernel

Timtheloon · 25 May 2020, 14:43

Quote:

Originally Posted by Hedeon

Thats a different library. And it removes the need for the env, not the jumper

Oh sorry didn’t realise is this going to be version 18? Or is it completely different?

Hedeon · 25 May 2020, 16:42

Not sure yet. Version 18 is in use by ReWarp. I probably stick to 17. It is intended for a more easy maintenance of the library. Adding stuff became more and more difficult (1MB of asm sources...).

The main motivator was Prometheus/Firestorm. And second to learn more C.

Any lingering A1200 support will be removed.

starship · 25 May 2020, 18:57

Hi hedeon

Anything for ragnarok+radeon128+100mbps eth card situation?

When the init old build (400 or older ) and softreset, all new builds are working.

Can be a way without softrestart?

starship · 01 June 2020, 18:15

It seems I must find 10mbit nic.

trixster · 01 June 2020, 19:22

RTL8029AS works fine

starship · 01 June 2020, 20:16

Thanks

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
WANTED: PCI Sound Card VORTEX2 SuperQuard / SQ2500 or Turtlebeach SantaCruz pci card	keropi	MarketPlace	12	15 March 2017 02:48
Wanted:Sonnet Technologies QuadDoubler 50 (Doubler 4000)	kronuz	MarketPlace	0	16 June 2013 00:29
eBay : Sonnet Quaddoubler	alexh	MarketPlace	3	07 May 2013 00:50
Overlay problem on GeForce 7200	Leandro Jardim	support.WinUAE	1	10 August 2010 15:50
Prometheus PCI & Voodoo 3 PCI GFX Card	Slayer	support.Hardware	21	05 September 2006 10:57

18 May 2020, 17:07	#3961
grelbfarlk Registered User Join Date: Dec 2015 Location: USA Posts: 2,902	@Johnnybarker did you set: -Harrier256MB (0 or 1): Enable if you have a Harrier based G4 card with 256MB. @TheMrKocour Yes due to the Spider using three IRQs, they are going to share with something. I haven't run the Sonnet in a long time but I was using the Spider with it successfully. Currently I have a Sphyder in with an Apocalypse and it basically works.

18 May 2020, 17:11	#3962
johnnybarker Registered User Join Date: Dec 2018 Location: Helmsdale Scotland Age: 41 Posts: 181	Oh, just reading the github again, looks like I may need to alter the envarc harrier =1? I know, RTFM. In the bath now so will try later.

18 May 2020, 17:14	#3963
johnnybarker Registered User Join Date: Dec 2018 Location: Helmsdale Scotland Age: 41 Posts: 181	Thanks grelbfarlk- screen refreshed too late to read your post before I replied to myself! Fingers crossed. I am hoping that if the RAM/soldering was dodgy then it would not work at all.

18 May 2020, 19:52	#3965
johnnybarker Registered User Join Date: Dec 2018 Location: Helmsdale Scotland Age: 41 Posts: 181	Hooray it works! Thanks again grelbfarlk for all the hard work you did in creating/testing this mod. Now that it is working I will admit that that I did go for the cheap RAM chips off Aliexpress.

18 May 2020, 21:48	#3969
Timtheloon Registered User Join Date: Dec 2017 Location: Portsmouth / United Kingdom Posts: 302	Hopefully I’ve bought the right ones

18 May 2020, 22:08	#3970
johnnybarker Registered User Join Date: Dec 2018 Location: Helmsdale Scotland Age: 41 Posts: 181	Looks good.

22 May 2020, 18:58	#3971
TheMrKocour Registered User Join Date: Apr 2018 Location: Prague, Czech Republic Age: 23 Posts: 34	Hi, any news on SheepShaver or iFusion?

25 May 2020, 10:49	#3973
Timtheloon Registered User Join Date: Dec 2017 Location: Portsmouth / United Kingdom Posts: 302	Hi I noticed this issue has been closed and marked as done on the GitHub. “Add an auto-detect routine for memory size for Apocalypse cards. #9” Does this mean we no longer need the jumper on 128mb cards?

25 May 2020, 13:01	#3974
Hedeon Semi-Retired Join Date: Mar 2012 Location: Leiden / The Netherlands Posts: 1,993	Thats a different library. And it removes the need for the env, not the jumper That one prevents booting of the card into its own kernel

25 May 2020, 16:42	#3976
Hedeon Semi-Retired Join Date: Mar 2012 Location: Leiden / The Netherlands Posts: 1,993	Not sure yet. Version 18 is in use by ReWarp. I probably stick to 17. It is intended for a more easy maintenance of the library. Adding stuff became more and more difficult (1MB of asm sources...). The main motivator was Prometheus/Firestorm. And second to learn more C. Any lingering A1200 support will be removed.

25 May 2020, 18:57	#3977
starship Registered User Join Date: Nov 2016 Location: turkiye Posts: 212	Hi hedeon Anything for ragnarok+radeon128+100mbps eth card situation? When the init old build (400 or older ) and softreset, all new builds are working. Can be a way without softrestart?

01 June 2020, 18:15	#3978
starship Registered User Join Date: Nov 2016 Location: turkiye Posts: 212	It seems I must find 10mbit nic.

01 June 2020, 19:22	#3979
trixster Guru Meditating Join Date: Jun 2014 Location: England Posts: 2,337	RTL8029AS works fine

01 June 2020, 20:16	#3980
starship Registered User Join Date: Nov 2016 Location: turkiye Posts: 212	Thanks

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)