has anyone dislodged CIAs from a rev 6a?? possible defect on rev 6a??

NfernalNfluence · 26 August 2007, 08:44

i have two different rev 6a motherboards and it's impossible to wedge even the smallest, a 1.4 mm flathead screw driver between CIAs & related sockets. there's absolutely no room to do this. the problem seems to only be restricted to "CIAs" on rev 6a. i just check a rev 5 to confirm this!!! what am i to do?

Jope · 26 August 2007, 20:23

If you have a thin screwdriver, you can work it under the chip by pushing it in and twisting/wiggling it about a bit.

You'll mar the socket a bit and also the underneath of the chip, but if you need to get them out, what else are you going to do?

The chips might be nicely oxidised into the sockets, so it will be stiff. But don't overdo it and ruin the legs of the chip by lifting one side up too much, try and have the screwdriver as horizontal as possible as you jam it between the chip & socket.

Chain · 27 August 2007, 09:29

forget screwdriver, try a knife

NfernalNfluence · 27 August 2007, 10:27

i did the best i could and finally removed the CIA (odd) then switch it with a CIA (odd) off a rev 5 . well, it didn't work. i'll try something else later

26 August 2007, 08:44	#1
NfernalNfluence Registered User Join Date: Feb 2007 Location: living among the Moai Posts: 219	has anyone dislodged CIAs from a rev 6a?? possible defect on rev 6a?? i have two different rev 6a motherboards and it's impossible to wedge even the smallest, a 1.4 mm flathead screw driver between CIAs & related sockets. there's absolutely no room to do this. the problem seems to only be restricted to "CIAs" on rev 6a. i just check a rev 5 to confirm this!!! what am i to do?

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
A500 Rev 4	platatomi	Hardware pics	12	29 August 2020 09:49
Differences between A2630 rev 9 to and rev 9.2	8bitbubsy	support.Hardware	0	21 May 2013 16:58
How do you know which kickstart rev you are using?	jt5566	support.Other	3	27 November 2011 16:07
Board Revision ADVICE Rev 1D.1 vs Rev 2B	W4r3DeV1L	support.Other	1	02 December 2008 23:44
A1200 REV 1.D1 versus A1200 REV 1.D4	eLowar	support.Hardware	6	28 April 2004 16:57

26 August 2007, 20:23	#2
Jope - Join Date: Jul 2003 Location: Helsinki / Finland Age: 43 Posts: 9,861	If you have a thin screwdriver, you can work it under the chip by pushing it in and twisting/wiggling it about a bit. You'll mar the socket a bit and also the underneath of the chip, but if you need to get them out, what else are you going to do? The chips might be nicely oxidised into the sockets, so it will be stiff. But don't overdo it and ruin the legs of the chip by lifting one side up too much, try and have the screwdriver as horizontal as possible as you jam it between the chip & socket.

27 August 2007, 09:29	#3
Chain A-Collector, repairments Join Date: Jul 2001 Location: Czech Rep. Age: 50 Posts: 1,536	forget screwdriver, try a knife

27 August 2007, 10:27	#4
NfernalNfluence Registered User Join Date: Feb 2007 Location: living among the Moai Posts: 219	i did the best i could and finally removed the CIA (odd) then switch it with a CIA (odd) off a rev 5 . well, it didn't work. i'll try something else later

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)