18 December 2020, 13:53 | #101 | |
Registered User
Join Date: Nov 2018
Location: Belfast
Posts: 1,526
|
I notice if I swap out MMUlib 68060.library for the Apollo 68060.library v60.10 I get slightly faster results. This just an experiment.
Quote:
So if I disable MuFastZero, MuMove4k, MuFastRom and MuMapRom, and just swap out these for RemApollo I should get better results again if I intend to mix both sets of tools? I will try Drap and MuDrap. So far I stripped all MMUlib stuff out of one HD and used solely the Apollo stuff and got better results. So now with another drive I am going to splice the two and I remove certain things of the MMUlib toolset and then utilize RemApollo basics. |
|
18 December 2020, 18:22 | #102 |
Registered User
Join Date: Oct 2009
Location: Germany
Posts: 3,304
|
Usually there should be only marginal differences in speed. Btw. what and how do you measure it? The most tools just configure you system to a given state without any speed impacts. For example if you map the Kick ROM to fastram the speed is given by the speed of fastram access and not by the tool who map the ROM. Important is that the tool works as expected and has no side effects.
As already mentioned there should be no problem using RemApollo and MuTools. Just make sure you don't do the same thing twice. |
08 May 2023, 00:13 | #103 | |
Registered User
Join Date: Feb 2013
Location: Dublin/Ireland
Posts: 403
|
Quote:
My setup is an A1200 with the Apollo 060 64mb ram and overclocked to 100mhz by Stanchu. I've been happily running this with ClassicWB 3.1 for years now using the above modified startup sequence which was provided by NovaCoder to get the best out of his and others projects. I'm now using OS 3.2 and the ClassicWB package. Basically, I had it booting fine before I got into the extra stuff, RemApollo, high speed maths etc. Now when I boot with the modified startup it just gets into a reboot loop and won't load. Is anyone successfully getting the above to work, and if so can you give me a dig out please! Thanks in advance. p.s I still have my working 3.1 setup on another CF card. |
|
08 May 2023, 13:28 | #104 | |
Registered User
Join Date: Nov 2018
Location: Belfast
Posts: 1,526
|
Quote:
Hmmm I have the same accelerator still and also a 3.2 setup that I've entirely switched over too. Now far as I remember you need MMULib installed on 3.2, are you using that ok? Seem to recall if are using other 060 libs then you need mDrap running. Also if I recall, how I got RemApollo working with 3.1 was I used to patcher provided to patch setpatch so I'm not sure if anything like that is required again whilst using in conjunction with 3.2. If I get time I'll swap my Apollo back into my main machine and run my 3.2 setup. Pretty sure it boots though if you use the Apollo 060 library along with MMUlib installed on 3.2. |
|
08 May 2023, 17:54 | #105 |
Registered User
Join Date: Feb 2013
Location: Dublin/Ireland
Posts: 403
|
Ah fair play, good shout. I am indeed using MMULIB and didn't think about mDrap. Will give it a go later and hopefully that'll do the job, thanks.
|
08 May 2023, 19:45 | #106 |
Registered User
Join Date: Nov 2018
Location: Belfast
Posts: 1,526
|
|
08 May 2023, 20:47 | #107 | |
Registered User
Join Date: Oct 2009
Location: Germany
Posts: 3,304
|
Just read the docs:
Quote:
|
|
10 May 2023, 23:31 | #108 |
Registered User
Join Date: Feb 2013
Location: Dublin/Ireland
Posts: 403
|
Thanks for the above advice, but I've had no joy. I am as you can no doubt tell, poor when it comes to this kinda stuff! I'm gonna start from scratch and do a fresh install of 3.2 and maybe leave the ClassicWB part for the moment. As far as editing the startup sequence etc, would it be possible to get a quick screenshot of it just to guide me in the right direction, be much appreciated! Thanks.
Edit: With a fresh install of OS3.2, updated to 3.2.2 and editing the startup sequence as above, I've got things working fine and speed wise it all seems to be working fine. Remains to be seen if I'll go with ClassicWB. Thanks for all your help. Last edited by Reido; 11 May 2023 at 03:06. |
11 May 2023, 11:55 | #109 | |
Registered User
Join Date: Nov 2018
Location: Belfast
Posts: 1,526
|
Quote:
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Apollo 1260 issue. | Pollock | support.Hardware | 20 | 20 September 2019 19:40 |
Strange Prefs (non) behaviour. | khph_re | support.WinUAE | 4 | 02 October 2010 14:34 |
Possible trade, Apollo 1260 @ 80mhz for Blizz 1260 | Molcos | Swapshop | 3 | 13 November 2009 16:13 |
Strange behaviour in p. illusions | _ThEcRoW | support.Games | 4 | 18 June 2007 18:17 |
Strange A1200 behaviour | manicx | support.Hardware | 39 | 09 November 2005 08:32 |
|
|