12 July 2010, 23:47 | #1 |
Zone Friend
Join Date: Jul 2005
Location: Toronto, Canada
Posts: 734
|
problem GVP techmagic 2060
I am trying to set up an A2000 with a Techmagic 060. The machine is a 6.2 version mobo. Currently I only have a buddha ide controller and a GVP spectrum board in it. I can't seem to get a stable system. I can't get more than 64 megs of ram after that the stability deteriorates dramatically. The machine will just randomly hang. I have tried 3 different power supplies, I have also tried a 4.5 revision mobo, but I have not had any luck. Last night the computer was booted u to aos39bb2 and spectrum screen. The screen blanker came on for the spectrum and the blanke was runnibg for a while, but again the computer froze. I can't seem to get things to work the way I think it should.
Any help would be greatly appreciated. |
13 July 2010, 00:33 | #2 | |
Ya' like it Retr0?
Join Date: Jul 2005
Location: United Kingdom
Age: 49
Posts: 9,768
|
@source
It does sound like a memory fault - not power fault - since you have tried several power supplies that for the most part concludes that. I would suggest that we isolate everything to determin the fault. just use the Techmagic no other card - remove the spectrum and the buddha - boot from the GVP 060 card.... do as much testing as you can - dumping stuff into fast ram from workbench - then once full - turn off and add more memory - keep going up in 16MB increments. heres what amiga.resource.cx has to say about the memory on the TekMagic Quote:
i.e have you got GVP SIMM's and regular PS/2 SIMMS together ? or a Mixed ammount? |
|
13 July 2010, 01:04 | #3 |
Zone Friend
Join Date: Jul 2005
Location: Toronto, Canada
Posts: 734
|
I am using 32 meg double sided 72 pin simms. I have 8 simms and have tried a number of different combinations. I still have to do the copy a lot of crap to ram: test yet.
|
13 July 2010, 02:08 | #4 |
I hate potatos and shirts
|
Try to lower the access speed to 80ns, even if you are using 60ns SIMM sticks. Might help on this problematic card.
|
15 July 2010, 18:19 | #5 |
Zone Friend
Join Date: Jul 2005
Location: Toronto, Canada
Posts: 734
|
I have cut down to just os3.1 and a scsi drive on the tekscsi. With 128 meg and so far the copy a crap load to ram disk has worked well. I did select for slower ram via jumper as well noticed there was no jumer on the rom select where the default was on pins and 2. When you intall os3.9, does it install its own version of the 68040.library and 68060.library and if so, could there be som compatibility problems with the os3.9 version that the original from the tekmagic install disk works better? When I have done the install, I started with the 3.1 install, then did the tekmagic install, then did the 3.9 install and the 2 boingbags, but I never re installed the tekmagic install after the 3.9 os.
Thanks |
15 July 2010, 18:39 | #6 |
Ya' like it Retr0?
Join Date: Jul 2005
Location: United Kingdom
Age: 49
Posts: 9,768
|
this may well be an 060 library fault?
did you re-install these as a matter of course with the 3.1 install ? Its quite likely that if you didn't do this with the 3.9os install then I am sure that issues / prolems and guru's will arise. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Trying to install a differnent files system on GVP 2060 | source | support.Hardware | 7 | 18 March 2013 06:15 |
GVP 040 Start up Sequence problem | psodas | support.Hardware | 5 | 24 August 2011 20:53 |
WTB : GVP Tekmagic 2040 or 2060 | CrashMidnick | MarketPlace | 0 | 11 July 2011 11:35 |
Kickrom 3.1 and GVP 1230+ problem | winloze99 | support.Hardware | 4 | 30 December 2005 20:06 |
GVP A530 SCSI problem | commie1974 | support.Hardware | 5 | 11 January 2005 18:43 |
|
|