Amiga 2000 rev 6.3 with a2620

cyberfox_it · 03 January 2014, 16:12

Hello,

I've a a2000 rev 6.3 with a a2620 with 2Mb installed, the problem is that sometimes it doesn't boot, sometimes boot perfectly.

The problem disappear if i remove the a2620, so the problem must be that.

Is there someone who had this problem and can give some hints ?

Thank you

alexh · 03 January 2014, 17:43

Could be hundreds of reasons. What happens when it doesn't boot?

1) Broken / dying hard drive?

Replace the hard drive, re-install Workbench and all A2620 related files. Does it still fail to boot?

2) Capacitor problems (either on the motherboard, PSU or the A2620)?

I'd start by measuring the voltage of the PSU and look to replace the capacitors in the PSU if anything isn't right. Then send the motherboard to Amigakit for recapping.

SpeedGeek · 03 January 2014, 17:49

Check the +5 Volt supply on the mobo (and A2620 if possible) as it probably drops when you install the A2620. You might also want to clean the 86 pin edge connector and re-seat any socket mounted chips (A2620 PALs in particular).

Good luck!

03 January 2014, 16:12	#1
cyberfox_it Registered User Join Date: Jun 2009 Location: Verona/Italy Age: 51 Posts: 38	Amiga 2000 rev 6.3 with a2620 Hello, I've a a2000 rev 6.3 with a a2620 with 2Mb installed, the problem is that sometimes it doesn't boot, sometimes boot perfectly. The problem disappear if i remove the a2620, so the problem must be that. Is there someone who had this problem and can give some hints ? Thank you

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
A2620 ROM Update	joeksterz	support.Hardware	20	28 November 2018 11:20
Wanted: rev 6.x Amiga 2000 motherboard	8bitbubsy	MarketPlace	2	02 September 2011 08:28
Board Revision ADVICE Rev 1D.1 vs Rev 2B	W4r3DeV1L	support.Other	1	02 December 2008 23:44
has anyone dislodged CIAs from a rev 6a?? possible defect on rev 6a??	NfernalNfluence	support.Hardware	3	27 August 2007 10:27
Amiga 2000 Rev 6 Mobo (8375 Agnus) PAL hack?	Six	support.Hardware	0	17 November 2004 20:24

03 January 2014, 17:43	#2
alexh Thalion Webshrine Join Date: Jan 2004 Location: Oxford Posts: 14,398	Could be hundreds of reasons. What happens when it doesn't boot? 1) Broken / dying hard drive? Replace the hard drive, re-install Workbench and all A2620 related files. Does it still fail to boot? 2) Capacitor problems (either on the motherboard, PSU or the A2620)? I'd start by measuring the voltage of the PSU and look to replace the capacitors in the PSU if anything isn't right. Then send the motherboard to Amigakit for recapping.

03 January 2014, 17:49	#3
SpeedGeek Moderator Join Date: Dec 2010 Location: Wisconsin USA Age: 60 Posts: 841	Check the +5 Volt supply on the mobo (and A2620 if possible) as it probably drops when you install the A2620. You might also want to clean the 86 pin edge connector and re-seat any socket mounted chips (A2620 PALs in particular). Good luck!

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)