12 February 2018, 09:44 | #1 |
Registered User
Join Date: May 2009
Location: Germany
Posts: 87
|
Workbench 1.3, FAT32 support failed
I use an Amiga 2000 with 2 AT-BUS 2008 controllers inside with oktapussy ROM. For quick data exchange I thought a CF card would be the best solution. Well, I downloaded at aminet the fat95 file and follwed the installation steps. After that, I modified DEVS:mountlist and add the commands as descripted on the instruction sheet. I changed the UNIT flag to 2nd.scsi.device and finishd all with #.
First, I mount my cf device with: mount cf: this works fine. But when I try to show the directory: dir cf: i get this error message: Could not get information for cf: Error 115 I don´t have the experience to solve this problem Maybe some skilled user here could give me further hints? |
12 February 2018, 11:00 | #2 |
Registered User
Join Date: Nov 2010
Location: Grenoble, Isère, Rhône-Alpes, France, Europe, Earth
Posts: 289
|
Be careful, the syntax of the 1.3 mountlist and 2.x is different.
Error 115 = bad number... Can you provide the mountlist text please... |
12 February 2018, 17:33 | #3 |
Registered User
Join Date: May 2009
Location: Germany
Posts: 87
|
Yes, here it is my mountlist:
PHP Code:
|
12 February 2018, 18:18 | #4 |
Registered User
Join Date: Nov 2010
Location: Grenoble, Isère, Rhône-Alpes, France, Europe, Earth
Posts: 289
|
BlockSize doesn't exist in 1.3, assumed to be 512...
1.3: BlocksPerTrack=1 2.x SectorsPerTrack=1 SectorSize=512 Tell if it fixes your problem. |
12 February 2018, 20:31 | #5 |
Registered User
Join Date: May 2009
Location: Germany
Posts: 87
|
Hi Giloo,
removing BlockSize makes no difference, still Error 115. I will make a try with a real harddisk to be sure that my CF card/CF reader dosen´t had any problem with the Amiga. I will correct myself, there ist a little mistake on Device, right is: PHP Code:
FD |
13 February 2018, 10:48 | #6 |
Registered User
Join Date: May 2009
Location: Germany
Posts: 87
|
Tested this morning with an IDE harddisk. Got the same error 115.
What is the meaning of 115 = bad number? Is there something wrong with my CF entry point on the mountlist? |
13 February 2018, 12:19 | #7 |
Registered User
Join Date: Nov 2010
Location: Grenoble, Isère, Rhône-Alpes, France, Europe, Earth
Posts: 289
|
And if you set HighCyl = 1 ?
|
13 February 2018, 14:20 | #8 |
Registered User
Join Date: May 2009
Location: Germany
Posts: 87
|
Hi,
I have news, a good and a bad one The bad one first, it is still not working with the posted configuration. The good one is, when I switch from 2nd.scsi.device to scsi.device and set unit = 1 (slave IDE port), then is the fat95 formatted diskdrive accessable. It looks like that the 2nd.scsi.device makes the trouble. I can´t explain why, I don´t have the knowledge to figure it out, but I can reconstruct the 115 error message. I think I would change my IDE chain and use the 2nd controller with PFS filesystem. Gilloo, thank you very much for your helpful hints. If you want further tests, I would be there P.S. : Changeing HighCyl makes no difference. Best regards FD |
14 February 2018, 11:19 | #9 |
Registered User
Join Date: Nov 2010
Location: Grenoble, Isère, Rhône-Alpes, France, Europe, Earth
Posts: 289
|
Perhaps there is an explanation:
scsi.device is the IDE port (you have the disk !) 2ndscsi.device is the SCSI port (sure you don't have anything in SCSI...) Last edited by Gilloo; 14 February 2018 at 11:20. Reason: syntax... |
16 February 2018, 15:01 | #10 |
Registered User
Join Date: May 2009
Location: Germany
Posts: 87
|
sorry for delay, no, both IDE controller are AT-Bus 2008.
An very interessting thing is, if you are using Oktopussy, you only need the ROM placed on one board and both boards responds. |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Cloanto 3.X Workbench Disks support | TuKo | project.ClassicWB | 23 | 13 January 2019 22:58 |
fat32 partition in RDB system | GhstWlf | support.Hardware | 2 | 23 July 2017 12:32 |
Mountlist for FAT32 4GB CF card? | BarryB | support.Hardware | 5 | 16 January 2014 00:16 |
Amiga SCSI mounting + Fat32 support | tekopaa | support.Hardware | 10 | 17 February 2013 14:03 |
Getting large hard drive support into Workbench 3.0/1 without idefix | Bloodwych | project.ClassicWB | 13 | 07 July 2009 23:14 |
|
|