English Amiga Board


Go Back   English Amiga Board > Support > support.Hardware

 
 
Thread Tools
Old 23 May 2020, 03:18   #1
psoma
Registered User

 
Join Date: Nov 2019
Location: Melbourne, Australia
Posts: 150
External FastMem with a TF534

Hi,

Am looking at getting myself a TF534 accelerator, but currently have a SCRAM 500 with 8MB Autoconfigure RAM. Had a couple of questions I'd like to run past the brains trust...

1) So the TF534 has 4MB of 32-bit RAM. If I disable 4MB in my SCRAM500 (it can run as 0, 2, 4 or 8MB), will Autoconfigure automatically pop 4MB from the TF534 and 4MB from the SCRAM500 in the correct memory addresses, or will they overlap?

2) If the former, will the system preference the 32-bit FastMem over the 24-bit sidecar FastMem?

Cheers!
psoma is offline  
Old 23 May 2020, 16:59   #2
hooverphonique
ex. demoscener "Bigmama"

 
Join Date: Jun 2012
Location: Fyn / Denmark
Posts: 1,096
I think the TF uses proper auto-config, so you shouldn't get an overlap - some of the TF's support using an address range outside 24 bits for its onboard ram (so you could keep all 8MB of SCRAM) , don't know about the 534 though.
Regarding the preference, it's entirely up to the priority the developer uses when the memory is added to the system - you can look up the priority of your SCRAM memory using something like SysInfo.
hooverphonique is offline  
Old 24 May 2020, 00:25   #3
psoma
Registered User

 
Join Date: Nov 2019
Location: Melbourne, Australia
Posts: 150
Thanks mate - so looks like the TF534 autoconfigures to Zorro III (530 did not), and I just read the SCRAM technical details (God bless the 80s/90s and their desire to share every intricate detail with us):

"Note that BORIS looks at the RAM SIZE jumpers JP1, JP2 to tell the Amiga
how much RAM is available (0/2/4/8 Meg). The DENNIS chip latches the RAM
BASE OFFSET at AutoConfig time. DENNIS then becomes the address space
decoder for RAM, selecting the four banks in ascending order.
The Amiga always allocates RAM from 200000 onwards. None, 2, 4, 8 Meg
are possible configurations. When other RAM devices precede the SCRAM,
the base offset will not be 200000, so note that some memory sizes will
be illegal. Most likely just 8 Megs, as this needs ALL the RAM space to
configure."

Seems like it is compatible, even if the TF534 mapped to Zorro II (I'd just have to disable 4MB on the SCRAM).

Off to market I go...
psoma is offline  
Old 24 May 2020, 11:41   #4
jbilander
Registered User

jbilander's Avatar
 
Join Date: Jun 2018
Location: Stockholm
Age: 44
Posts: 141
The TF534 will autoconfig to Z3 space so shouldn't conflict. I think the TF534's 4MB 32-bit RAM will be given higher priority config automatically but I'm not sure. That is however important because the accelerator CPU has to insert wait states when talking to the 7 MHz bus (glue logic) = slow, whilst when talking to the 4MB onboard SRAM it is a matter of "don't tell the Amiga about it" and run full speed. The TF534 is obsoleted/not worked on any more and replaced with the TF536.
jbilander is offline  
Old 25 May 2020, 02:01   #5
psoma
Registered User

 
Join Date: Nov 2019
Location: Melbourne, Australia
Posts: 150
Yeah, I've ordered a TF534 for now and will report back on the autoconfigure/priority situation. I realise the TF536 is the going concern but my understanding is there are no pre-built boards available yet, so the TF534 will (hopefully) tide me over until I upgrade to the TF536 down the track.

Cheers all!
psoma is offline  
 


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Similar Threads
Thread Thread Starter Forum Replies Last Post
TF534 Firmware updates ? prl1975au support.Hardware 1 26 April 2020 11:37
Setup of tf534 ikorodu Hardware mods 2 13 April 2020 03:38
Amiga 500 FastRAM expansion - internal (68k socket) vs external (Zorro) JanHolbo Hardware mods 2 15 January 2020 15:03
TF534 and Buddha ide Madk71 support.Hardware 29 15 October 2019 16:00
A600 4mb Fastram + A1200 Mb Fastram mikele MarketPlace 7 07 May 2012 19:28

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +2. The time now is 00:01.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
Page generated in 0.08074 seconds with 15 queries