01 December 2016, 22:57 | #61 |
Registered User
Join Date: Oct 2016
Location: Berks, UK
Posts: 269
|
I'm paid up, still showing allocated. Wonder if it will arrive for Christmas
|
01 December 2016, 23:41 | #62 |
Registered User
Join Date: Sep 2006
Location: Thunder Bay, Canada
Posts: 4,323
|
half of batch 1 was mailed today, other half hopefully tomorrow, begin mailing batch 2 and collecting remaining money next week, batch 2 should all be delivered by xmas (unless you live in Italy lol). Also, the first part of batch 3 will be mailed. (first paid gets the early board
What a lot of work in mailing, i really really hate this part |
02 December 2016, 19:23 | #63 |
Registered User
Join Date: Sep 2006
Location: Thunder Bay, Canada
Posts: 4,323
|
finally got new screws ii been looking for, this is the new mounting system from now on. (no drilling required)
www.kipper2k.com/video/shakeme.avi Last edited by kipper2k; 02 December 2016 at 19:35. |
02 December 2016, 19:36 | #64 | |
Registered User
Join Date: Oct 2012
Location: Krypton
Posts: 1,210
|
Quote:
what are the dimensions you have for the stand offs and screws ?, I found that the 2mm x 15mm long screws are good to use but you will have to drill the slots with a 2mm drill first, also I used some nylon stand offs similar to yours which were 8mm long on my Furia ,like these http://www.ebay.co.uk/itm/4003281924...%3AMEBIDX%3AIT |
|
02 December 2016, 19:39 | #65 | |
Registered User
Join Date: Sep 2006
Location: Thunder Bay, Canada
Posts: 4,323
|
Quote:
screws are 1.6mm x 16mm (nuts obviously 1.6mm too. Gap between mobo and bottom of vampire is approx 8mm, screws fit through the holes with no drilling. On a side note, i have to have hand surgery (again) on Monday, so i am going to try to get all of batch 2 done prior to tis, and then i am out of action for about 3 weeks. (which is about same time as the arrival of batch 3) |
|
02 December 2016, 19:48 | #66 |
Registered User
Join Date: Oct 2012
Location: Krypton
Posts: 1,210
|
Excellent news you got those special size screws, and best wishes for the op buddy.
|
02 December 2016, 20:08 | #67 |
Registered User
Join Date: Feb 2012
Location: #DrainTheSwamp
Posts: 4,545
|
|
02 December 2016, 21:49 | #68 |
Registered User
Join Date: Nov 2009
Location: Blyth England
Age: 68
Posts: 786
|
All the best for your hand surgery and don't force it to do anything strenuous until its recovered and ready for some action, your health and well-being is more important in the long run
|
08 December 2016, 16:02 | #69 |
Registered User
Join Date: Oct 2015
Location: US
Posts: 284
|
Best wishes for your surgery kippet2k! Next time, remember that the hot end of the iron goes DOWN
|
08 December 2016, 16:04 | #70 |
Inviyya Dude!
Join Date: Sep 2016
Location: Amiga Island
Posts: 2,770
|
|
24 December 2016, 20:17 | #71 |
Posts: n/a
|
Mine arrived today- Midwest USA. The HDMI connector is unpopulated- is that expected!
Thanks! And very sorry to hear about the hand surgery- it's a bitch- be sure to do the (painful) physical therapy. Thanks again! |
24 December 2016, 21:01 | #72 |
Registered User
Join Date: Oct 2012
Location: Krypton
Posts: 1,210
|
|
26 December 2016, 16:38 | #73 |
Registered User
Join Date: Sep 2016
Location: Michigan
Posts: 384
|
|
02 April 2023, 18:29 | #74 | |
Registered User
Join Date: Aug 2018
Location: Roseville, CA, USA
Posts: 18
|
Quote:
|
|
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
Vampire 600 and floppy issues | Firestone | support.Hardware | 15 | 22 March 2017 18:11 |
First Amiga 600 FPGA Accelerator - Vampire 600 | majsta | Hardware mods | 736 | 18 July 2016 18:31 |
Vampire 600 more cores.. | Turran | support.Hardware | 48 | 14 January 2015 17:39 |
Vampire 600 wierd issues | Retro | support.Other | 4 | 05 September 2014 22:36 |
Vampire 600 troubles | Viserion | support.Hardware | 21 | 10 December 2013 20:28 |
|
|