15 April 2017, 19:19 | #1 |
Registered User
Join Date: Apr 2011
Location: birmingham
Age: 55
Posts: 2,827
|
california access malibu boot rom
as in title i can dump the bootrom for this device,while i still have the machine here for repair
apparently its needed? let me know and ill dump it through my programmer its only about 8k ill need to know quick as itll be due to go back next week,i cant remember where i read it,i think it was winuae website? |
15 April 2017, 19:21 | #2 |
WinUAE developer
Join Date: Aug 2001
Location: Hämeenlinna/Finland
Age: 49
Posts: 26,517
|
Yes, please! Any Amiga expansion ROM/EPROM should be always dumped, even if it seems useless
EDIT: Could you also take photo of the board? |
15 April 2017, 19:24 | #3 |
Registered User
Join Date: Apr 2011
Location: birmingham
Age: 55
Posts: 2,827
|
okie dokie ill dump the bootrom in a minute
give me a few minutes to pull the card and compact the file and dump it in the zone |
15 April 2017, 19:27 | #4 |
WinUAE developer
Join Date: Aug 2001
Location: Hämeenlinna/Finland
Age: 49
Posts: 26,517
|
And one more thing: output from WB2.x+ "tools/showconfig debug", thanks.
|
15 April 2017, 19:31 | #5 |
Registered User
Join Date: Apr 2011
Location: birmingham
Age: 55
Posts: 2,827
|
its in the zone
ill have a look at that in a sec tony |
15 April 2017, 20:51 | #6 |
Registered User
Join Date: Apr 2011
Location: birmingham
Age: 55
Posts: 2,827
|
excuse my ignorance but where is that exactly?
|
15 April 2017, 21:02 | #7 |
WinUAE developer
Join Date: Aug 2001
Location: Hämeenlinna/Finland
Age: 49
Posts: 26,517
|
What is where? showconfig? It is located on WB disk (sys:tools/showconfig) Type "sys:tools/showconfig debug >output.txt" in shell.
If you need 1.x compatible program, use this: http://www.winuae.net/files/b/expdump.zip |
16 April 2017, 11:35 | #8 |
Registered User
Join Date: Apr 2011
Location: birmingham
Age: 55
Posts: 2,827
|
ill try that later
i seen your edit,its the same board in the big book of amiga hardware,so im not sure sure a picture of the board is needed this machine is under 2.04 i think i was trying to find showconfig but couldnt find it |
16 April 2017, 13:04 | #9 |
WinUAE developer
Join Date: Aug 2001
Location: Hämeenlinna/Finland
Age: 49
Posts: 26,517
|
Yes, that photo was good enough. I only needed to know which SCSI chip it uses. (It was usual 5380)
Auotoconfig dump (via showconfig or expdump, unfortunately most other system info programs don't list the boot rom vector offset) is needed to know the exact address of boot ROM. EDIT: Showconfig is located at least on 2.1 and 3.1 Extras disk (not WB). It does not seem to be included with 2.0. Last edited by Toni Wilen; 16 April 2017 at 13:11. |
16 April 2017, 13:10 | #10 |
Registered User
Join Date: Apr 2011
Location: birmingham
Age: 55
Posts: 2,827
|
yes, it does use a 5380
ill see if i can have a look later tony,and try to report back |
16 April 2017, 13:34 | #11 |
Registered User
Join Date: Apr 2011
Location: birmingham
Age: 55
Posts: 2,827
|
Board + Rom (HD?) (unidentified): Prod=2065/1($811/$1) (@$E90000 64K)
hope that helps a bit |
16 April 2017, 13:40 | #12 |
WinUAE developer
Join Date: Aug 2001
Location: Hämeenlinna/Finland
Age: 49
Posts: 26,517
|
|
16 April 2017, 13:47 | #13 |
Registered User
Join Date: Apr 2011
Location: birmingham
Age: 55
Posts: 2,827
|
ok ill try again
is there a way to do this from floppy? ill give it a go if there is a way i cant mess with the harddrive,i have instructions to leave that be EDIT: if there is a way to drop it into the harddrive and run it,ill do that,i can remove it afterwards EDIT2: hang on i have an idea |
16 April 2017, 14:04 | #14 |
Registered User
Join Date: Apr 2011
Location: birmingham
Age: 55
Posts: 2,827
|
ok i got it give me a while to type it out
|
16 April 2017, 14:17 | #15 |
WinUAE developer
Join Date: Aug 2001
Location: Hämeenlinna/Finland
Age: 49
Posts: 26,517
|
You mean the expdump output? Only the 16 byte hex string is needed, you can ignore all the other lines.
|
16 April 2017, 14:23 | #16 |
Registered User
Join Date: Apr 2011
Location: birmingham
Age: 55
Posts: 2,827
|
Board + Rom (HD?) (unidentified): Prod=2065/1($811/$1) (@$E90000 64K)
ConfigDev structure found at location $C18 === Board ID (Expansion Rom) information: er_Manufacturer =2065=£811=("$F7EE) er_Product =1=$1=("$FE) er_Type =$D1 (type 3,size 64K, not for free list, ROM diag vec valid, not chained) er_flags =$0 (no space preference,can be shut up) er_InitDiagVec =$4000 DiagCopy at =$20088 === Configuration (ConfigDev) information: cd_BoardAddr =$E9000 cd_BoardSize =$1000 (64K) cd_Flags =$1 (CONFIGME bit cleared =========================================== is that enough info tony? |
16 April 2017, 14:24 | #17 |
WinUAE developer
Join Date: Aug 2001
Location: Hämeenlinna/Finland
Age: 49
Posts: 26,517
|
Yes, that is exactly what I needed, thanks! (InitDiagVec was the most important)
EDIT: if you aren't too bored yet, could you check if any value changes when controller is in non-autoboot mode? D1 may change to C1 or er_InitDiagVec may change. Others probably stay the same. |
16 April 2017, 14:29 | #18 |
Registered User
Join Date: Apr 2011
Location: birmingham
Age: 55
Posts: 2,827
|
ill have a look in a bit im having a cuppa
you mean physically setting the card to not autoboot via its jumper? |
16 April 2017, 14:47 | #19 |
WinUAE developer
Join Date: Aug 2001
Location: Hämeenlinna/Finland
Age: 49
Posts: 26,517
|
|
16 April 2017, 14:54 | #20 |
Registered User
Join Date: Apr 2011
Location: birmingham
Age: 55
Posts: 2,827
|
yes,D1 does indeed change to C1
er_InitDiagVec doesnt change |
Currently Active Users Viewing This Thread: 1 (0 members and 1 guests) | |
Thread Tools | |
Similar Threads | ||||
Thread | Thread Starter | Forum | Replies | Last Post |
EUAE on MacOSX PPC - no CD ROM access | Reth | support.OtherUAE | 0 | 24 May 2015 00:59 |
i need rom... a4091 scsi boot rom | elmorcilla | support.WinUAE | 10 | 22 August 2014 00:59 |
support for AROS boot rom | Worfje | support.WinFellow | 16 | 16 November 2011 21:43 |
Malibu rom | tomse | support.Hardware | 0 | 04 July 2010 10:09 |
|
|