Mediator 4000Di and Indivision AGA 4000

trixster · 03 November 2016, 14:17

Hi,

Does anyone know if the Mediator 4000Di and daughterboard fit in an A4000 when an Indivision AGA 4000 is already installed?

Thanks.

Magic · 03 November 2016, 16:25

Yes it does fit. It works well in my A4000D

trixster · 03 November 2016, 19:00

Just to check, I'm talking about the original Indi AGA which is the first picture, not the Mk2 which is the second one.

How much clearance is there between the bottom side of the daughterboard and the top of the Indivision?

Magic · 03 November 2016, 20:40

Sorry, mine looks like the red one in the second picture.

cmsj · 04 November 2016, 10:36

Hey

Quote:

Originally Posted by trixster

How much clearance is there between the bottom side of the daughterboard and the top of the Indivision?

I don't have a strict measurement for you, but I will say that my 4000Di3 daughterboard has a bit of up/down movement to it, so while I think the two *could* fit together, I would *definitely* be insulating the top of the Indi.

I already put electrical tape over all of the jumper pins on the 4000 motherboard, because the Mediator bridgeboard was able to touch some of them.

trixster · 04 November 2016, 11:11

Good info, thanks. My Indi has the resistor mod so it's a mm or two higher than a standard Indi as it is.

jkdsteve · 26 March 2021, 05:32

What about heat though? I hear the Indy gets quite warm, as does the Mediator.

trixster · 26 March 2021, 08:45

It’s fine

spudje · 26 March 2021, 15:07

It fits, but the combination was causing my system to crash in resource intensive PPC Warp3D games. Confirmed it was heat with blowing a big ventilation fan (no crashes), vs without the fan (crashes). I swapped any other component which resulted in the same crashes. So it was heat from either the indivision or mediator logic card (or the combination).

03 November 2016, 14:17	#1
trixster Guru Meditating Join Date: Jun 2014 Location: England Posts: 2,337	Mediator 4000Di and Indivision AGA 4000 Hi, Does anyone know if the Mediator 4000Di and daughterboard fit in an A4000 when an Indivision AGA 4000 is already installed? Thanks.

03 November 2016, 19:00	#3
trixster Guru Meditating Join Date: Jun 2014 Location: England Posts: 2,337	Just to check, I'm talking about the original Indi AGA which is the first picture, not the Mk2 which is the second one. How much clearance is there between the bottom side of the daughterboard and the top of the Indivision? Attached Thumbnails

Similar Threads
Thread	Thread Starter	Forum	Replies	Last Post
Is Indivision AGA MkIIcr compatible with Video Toaster 4000 in a 4000?	pgovotsos	support.Hardware	0	07 January 2016 05:26
Indivision AGA Mk2 and Video Toaster 4000?	Pyromania	support.Hardware	3	16 August 2013 11:16
Amiga 4000, Indi MKII and Mediator 4000Di	jvdw007	support.Hardware	2	21 June 2012 00:40
[WTB] Indivision AGA (for CD32/4000) + Indivision ECS	Seaside	MarketPlace	3	15 March 2012 22:03
Indivision AGA 4000 and CD32	amigakit.com	News	29	17 February 2009 12:56

03 November 2016, 16:25	#2
Magic Registered User Join Date: Aug 2007 Location: USA Posts: 359	Yes it does fit. It works well in my A4000D

03 November 2016, 20:40	#4
Magic Registered User Join Date: Aug 2007 Location: USA Posts: 359	Sorry, mine looks like the red one in the second picture.

04 November 2016, 11:11	#6
trixster Guru Meditating Join Date: Jun 2014 Location: England Posts: 2,337	Good info, thanks. My Indi has the resistor mod so it's a mm or two higher than a standard Indi as it is.

26 March 2021, 05:32	#7
jkdsteve Registered User Join Date: Dec 2020 Location: USA Posts: 67	What about heat though? I hear the Indy gets quite warm, as does the Mediator.

26 March 2021, 08:45	#8
trixster Guru Meditating Join Date: Jun 2014 Location: England Posts: 2,337	It’s fine

26 March 2021, 15:07	#9
spudje Registered User Join Date: Dec 2014 Location: Netherlands Posts: 1,406	It fits, but the combination was causing my system to crash in resource intensive PPC Warp3D games. Confirmed it was heat with blowing a big ventilation fan (no crashes), vs without the fan (crashes). I swapped any other component which resulted in the same crashes. So it was heat from either the indivision or mediator logic card (or the combination).

Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)