English Amiga Board


Go Back   English Amiga Board > Support > support.Other

 
 
Thread Tools
Old 27 September 2019, 20:54   #1
mcgeezer
Registered User

 
Join Date: Oct 2017
Location: Sunderland, England
Posts: 1,487
Stripping label and glue from floppies

Hi all,

In my GCSE's I got a F in Chemistry and I'm no Walter White.

If I want to strip the excess glue and label from a floppy disk is using White Spirit ok to use?

Geezer
mcgeezer is offline  
Old 27 September 2019, 21:22   #2
deimos
Registered User

 
Join Date: Jul 2018
Location: Londonish / UK
Posts: 441
Dunno, but a good glue remover is LRM Label Remover (https://cpc.farnell.com/electrolube/...l/dp/SALRM200D), but obviously you've got to make sure the disk inside is kept clean and damage free, which is going to be hard with any approach.
deimos is online now  
Old 27 September 2019, 21:25   #3
solarmon
Registered User

solarmon's Avatar
 
Join Date: Dec 2018
Location: UK
Posts: 510
I would use isopropyl alcohol. I use it to clean the floppy disk media inside it, so I know it is safe.
solarmon is offline  
Old 28 September 2019, 13:17   #4
Hewitson
Registered User
Hewitson's Avatar
 
Join Date: Feb 2007
Location: Melbourne, Australia
Age: 37
Posts: 3,381
I'd use metho (methylated spirits).
Hewitson is offline  
Old 28 September 2019, 15:40   #5
sTe
Registered User

 
Join Date: Aug 2018
Location: Mansfield
Posts: 61
When I used to strip labels off disks, depending if they was nice thick labels I used to use a hot water bottle, rapped in tea towel and then put the disk / label side on the towel and ever so often try to peal the label off. If it was those really cheap labels ... that was never fun, and never pealed nicely. Heat probably not good for disks ... but 20 odd years ago, i didnt worry so much.

Last edited by sTe; 28 September 2019 at 20:13.
sTe is offline  
Old 28 September 2019, 23:30   #6
matburton
Registered User

matburton's Avatar
 
Join Date: Apr 2017
Location: Cambridge
Posts: 93
I tend to use White Spirit and it works fine.

Here's what I do:
1. Use a small paint brush to completely saturate the label
2. Leave for 15 minutes or so
3. Peel slowly, most of the time the whole label comes off at once, don't rip or force it
4. Use the paint brush again on the revealed surface
5. Wipe with a cloth to remove any stickiness

If the label doesn't look like it's going to come of the first time I give it another round. But a second time and I just give-up, because picking at labels takes too much time.

The key is to do loads at once because of the wait time.
matburton is offline  
Old 29 September 2019, 15:42   #7
idrougge
Registered User
 
Join Date: Sep 2007
Location: Stockholm
Posts: 3,927
I use Kontakt Chemie Etikettenlöser.

Last edited by idrougge; 21 October 2019 at 02:45.
idrougge is offline  
Old 29 September 2019, 19:08   #8
sneeker
Registered User

 
Join Date: Mar 2008
Location: Manchester!
Posts: 197
I used to use my mums nailpolish remover back in the day, Nowerdays I very rarely use floppys so just have some I label with pencil and rub it out if needs be.
sneeker is offline  
Old 29 September 2019, 23:02   #9
BarryB
Amigaholic

 
Join Date: Dec 2009
Location: UK
Posts: 3,048
I use some of my Electrolube LFFR (Lead Free Flux Remover), only because it smells so sweet and gets you high
BarryB is offline  
Old 02 October 2019, 21:28   #10
Juz400
Registered User

 
Join Date: Mar 2017
Location: London
Posts: 69
Back in the day, stripped the labels of prob over 10K disks
Zippo lighter fluid was cheap and plentiful and worked well, even on the glossy ones if left to partially evaporate and a second coating applied.
A less flammable method is to use a handheld hair drier, warm the label up for a minute or so and gently peal.

Above all, PATIENCE, dont rush it, warm it a bit more if it isnt lifting, same goes for fluids!
the zippo got `bits` of labels off too and all the glue residue
Juz400 is offline  
Old 04 October 2019, 20:42   #11
paul1981
Registered User

paul1981's Avatar
 
Join Date: Oct 2013
Location: England
Posts: 178
I'd use WD-40, and once removed, IPA to clean away the oil.
paul1981 is offline  
Old 21 October 2019, 02:46   #12
idrougge
Registered User
 
Join Date: Sep 2007
Location: Stockholm
Posts: 3,927
I just read a tip in a German magazine to use a cotton pad with terpentine to soak the label, then peel it off and do any clean up of remaining glue with the same pad.
idrougge is offline  
Old 21 October 2019, 06:41   #13
ptyerman
Registered User

ptyerman's Avatar
 
Join Date: Jun 2012
Location: Worksop/UK
Age: 55
Posts: 1,244
I use part vinegar part hot water for some stuff, its usually stuff I can leave soaking in it for a while though. Does a grand job on bottle labels and the like.
Not tried it on floppys and you obviously can't leave them to soak in the solution.
ptyerman is offline  
 


Currently Active Users Viewing This Thread: 1 (0 members and 1 guests)
 
Thread Tools

Similar Threads
Thread Thread Starter Forum Replies Last Post
Disk Label Dimensions Methanoid Retrogaming General Discussion 6 20 July 2018 01:59
which glue for a CPU fan? TheDarkCoder support.Hardware 23 29 August 2015 00:36
Dopus 4 disk label videofx request.Other 2 08 June 2014 03:00
Amiga and C64 case plastic... How to glue? ElectroBlaster support.Hardware 1 04 February 2014 09:28
Label Program for Amiga moxavius support.Apps 2 18 February 2012 14:59

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off

Forum Jump


All times are GMT +2. The time now is 12:22.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2019, vBulletin Solutions Inc.
Page generated in 0.07724 seconds with 15 queries