OS 4.1 FE Update 1: Expand RAM On WinUAE?

[elowan]

Originally Posted by SnkBitten

I did the update, made sure my WinUAE OS4.1 setup started and then made the change to s:startup-sequence.

I then used F12 "Restart" and relaunched the OS4.1 setup and additional memory was there. Did you control-amiga-amiga or restart? The update I believe does some kickstart patching which may need a "power off" vs. just rebooting.

hmmm, so I have to update 1st, before putting C:BootLoader COMMANDLINE="NoRamPager" in the s-s?? thought it would not matter...

[SnkBitten]

It probably doesn't. Just showing how I updated without issue.

[elowan]

ok, I tried to install update 1st, then boot and change the s-s ... but seems like the update breaks my system everytime! no luck at all... after installing, OS is brocken

[Snake79]

Good would be to attach config file of yours (and logs).

[AMIGASYSTEM]

Originally Posted by elowan

I got os 4.1Fe classic runnin in WinUAE 3.4 (got the 32 and 64bit version)
... the rebbot shows just the pinky screnn of death

If you want to restart OS4.1 got stuck on the pink, you have to replace the folder "KickStart" and its contents, then maybe repeat the update

[Snake79]

Maybe this can help somehow? Config (with ES1370 and RTL8029 on Mediator) attached.

[elowan]

ok, here are the logs, after update 1 was installed

[elowan]

Originally Posted by AMIGASYSTEM

If you want to restart OS4.1 got stuck on the pink, you have to replace the folder "KickStart" and its contents, then maybe repeat the update

you mean the kickstart folder of winuae, where the rom files are located? this does not work...

[Snake79]

I have tested config of yours and it is booting with my vhd (without sound card and lan) but fine.. Strange.. Maybe you should remove every hdd but left only os one and try again?.. You can also try my config.. Add os hdd of yours. Config attached..

[Toni Wilen]

Bad CSPPC boot menu settings?

[elowan]

Originally Posted by Snake79

I have tested config of yours and it is booting with my vhd (without sound card and lan) but fine.. Strange.. Maybe you should remove every hdd but left only os one and try again?.. You can also try my config.. Add os hdd of yours. Config attached..

I removed all drives, except for OS of course from WinUAE config - but it´s not working... pinky screen still

[FOL]

Originally Posted by elowan

I removed all drives, except for OS of course from WinUAE config - but it´s not working... pinky screen still

I used to get stuck at pink screen, if I hadnt set low latency vsync in the video settings. So I set both RTG and Chipset to low latency vsync.

[AMIGASYSTEM]

Originally Posted by elowan

you mean the kickstart folder of winuae, where the rom files are located? this does not work...

No, the folder "Kickstart" on OS4.1, you have to replace the old one if you have a copy

[elowan]

Originally Posted by AMIGASYSTEM

No, the folder "Kickstart" on OS4.1, you have to replace the old one if you have a copy

oh - I see! but I can not access the hdf file anymore, because it does not boot - how do I supposed to change some files on this?

for now, I just copy over my backup diskfile and boom, OS 4.1fe is back to life... but still no update1 for me

tried a few times now, but no success at all

[elowan]

Originally Posted by FOL

I used to get stuck at pink screen, if I hadnt set low latency vsync in the video settings. So I set both RTG and Chipset to low latency vsync.

Ok, I try this - but how does updating OS4.1 affect the WinUAE settings?

I mean, before the update, it was all good...

[FOL]

Originally Posted by elowan

Ok, I try this - but how does updating OS4.1 affect the WinUAE settings?

I mean, before the update, it was all good...

Easy. It doesnt. You sure you havent updated winuae and that your old config is not broken. If I update winuae, I normally load old config, then save as new one. This tends to correct errors in old config for updated winuae.

Sent from my SM-G900F using Tapatalk

[elowan]

hmmm, I also updated WinUAE from an older public Beta to 3.4 release and load/saved the old config...

[elowan]

no luck for me - tired everything, but nothings works! sadly, no Update 1 and more RAM for me.

thanks everybody for helping!

[AMIGASYSTEM]

Originally Posted by elowan

oh - I see! but I can not access the hdf file anymore, because it does not boot - how do I supposed to change some files on this?

Simple, mount HD OS4.1 on another Amiga system working example OS3

[elowan]

Originally Posted by AMIGASYSTEM

Simple, mount HD OS4.1 on another Amiga system working example OS3

not that simple, I guess. I try to mount, but the faulty OS4.1 install does not mount/show on workbench, but I configured it in WinUAE (see image)