English Amiga Board


Go Back   English Amiga Board > Search Forums

Showing results 1 to 40 of 6680
Search took 0.55 seconds.
Search: Posts Made By: Jope
Forum: support.Hardware Today, 05:29
Replies: 9
Views: 287
Posted By Jope
It's available in the RGB port, the video slot...

It's available in the RGB port, the video slot and the Zorro 3 slots. You may or may not need it, depending on what you plug into the machine.
Forum: support.Hardware Yesterday, 20:01
Replies: 1
Views: 66
Posted By Jope
If it's only whdload installs that you need, then...

If it's only whdload installs that you need, then those are rather easily available online. Naturally any saved games would be lost.

Apart from that, it's dd_rescue and patience I'm afraid.
Forum: Hardware mods Yesterday, 19:20
Replies: 101
Views: 4,679
Posted By Jope
http://aminet.net/package/docs/hard/IDE_Killer

http://aminet.net/package/docs/hard/IDE_Killer
Forum: News Yesterday, 15:43
Replies: 28
Views: 3,881
Posted By Jope
Thanks for the info. Is this project ready to go?

Thanks for the info. Is this project ready to go?
Forum: News 16 July 2018, 11:03
Replies: 28
Views: 3,881
Posted By Jope
Only the MC-702, and that is only Z2...

Only the MC-702, and that is only Z2 http://amiga.resource.cx/exp/mastercard
Forum: support.Hardware 15 July 2018, 10:41
Replies: 4
Views: 186
Posted By Jope
If you are going to use the trapdoor slot and...

If you are going to use the trapdoor slot and 512k on the motherboard, just adjust JP7 and JP2. If you don't want to adjust JP7, you can use the switch on your trapdoor memory expansion.
Forum: support.Hardware 15 July 2018, 10:39
Replies: 9
Views: 273
Posted By Jope
I reread your question and came to the same...

I reread your question and came to the same conclusion as Stachu.. Probably scaling side effects.

The short circuits I referred to are on the solder side of the riser, around the area where the...
Forum: support.Hardware 12 July 2018, 21:01
Replies: 9
Views: 287
Posted By Jope
Also check out SFX power supplies.

Also check out SFX power supplies.
Forum: support.Hardware 12 July 2018, 21:00
Replies: 9
Views: 273
Posted By Jope
Check behind the zorro riser for bent/shorted...

Check behind the zorro riser for bent/shorted pins first.
Forum: support.Hardware 11 July 2018, 21:31
Replies: 5
Views: 211
Posted By Jope
True, 3.0 has the old 37.11 card.resource. ...

True, 3.0 has the old 37.11 card.resource.

Was it a bug that card.resource allows overlapping cards or was it a bug that they fixed the overlap problem to also shut up cards that don't overlap.....
Forum: support.Hardware 11 July 2018, 20:38
Replies: 5
Views: 211
Posted By Jope
Edit: oops, was too quick. Find eight pieces...

Edit: oops, was too quick.

Find eight pieces of 1Mx4 ZIPs and populate the second bank. You will lose access to the PCMCIA slot unless you patch your card.resource.
Forum: support.Hardware 11 July 2018, 20:23
Replies: 261
Views: 22,989
Posted By Jope
You probably won't need the Zer0-X tool, all...

You probably won't need the Zer0-X tool, all known disks have already been deprotected with it and are available in my google drive link elsewhere in this thread.

I started modifying another tool...
Forum: support.Hardware 10 July 2018, 21:07
Replies: 15
Views: 647
Posted By Jope
This might help. Display lives in sys:utilities

This might help. Display lives in sys:utilities
Forum: Nostalgia & memories 09 July 2018, 21:50
Replies: 60
Views: 6,277
Posted By Jope
Apparently the choice was 1MB Chip + HD floppy...

Apparently the choice was 1MB Chip + HD floppy drive or 2MB Chip and a DD drive. We all know what they decided upon. :-)
Forum: support.Hardware 09 July 2018, 20:33
Replies: 15
Views: 647
Posted By Jope
Seems to me, like the only actual difference is...

Seems to me, like the only actual difference is in the setclock binary, which the install disk copies from itself to the WB partition after all the files have been copied.

The installer also...
Forum: support.Hardware 09 July 2018, 17:07
Replies: 15
Views: 647
Posted By Jope
The original disk set included with the early...

The original disk set included with the early A3000s has six disks.
- kickstart
- install
- wb1.3.2
- extras 1.3
- wb 2.0
- extras 2.0

The install disk has PrepHD, FormatHD and InstallHD...
Forum: support.Hardware 09 July 2018, 16:57
Replies: 3
Views: 168
Posted By Jope
That's how they are when the gun is constantly...

That's how they are when the gun is constantly firing, red raster + visible retrace lines.
Forum: support.Hardware 07 July 2018, 08:26
Replies: 3
Views: 168
Posted By Jope
Red gun stuck on. Perhaps some gunk inside the...

Red gun stuck on. Perhaps some gunk inside the tube has fallen into the electron gun and is now shorting it. Unless you had one of the transistors for driving the red gun fail on the chassis or neck...
Forum: support.Hardware 07 July 2018, 08:20
Replies: 5
Views: 254
Posted By Jope
Keep the ROMs in the sockets you found them in,...

Keep the ROMs in the sockets you found them in, the machine will not boot at all if you swap them around.
Forum: support.Hardware 05 July 2018, 10:14
Replies: 15
Views: 647
Posted By Jope
Do you have some version of FFS on the RDB in...

Do you have some version of FFS on the RDB in addition to PFS3?

KS1.3 doesn't have a resident FFS, so one must be present on the RDB.
Forum: support.Hardware 04 July 2018, 13:20
Replies: 15
Views: 647
Posted By Jope
The bonus hides the OS's partition for the other...

The bonus hides the OS's partition for the other kickstart when you boot from the hard disk. IIRC they are all visible if you boot from a floppy.

FFS should be fine, but it can't be too new.
Forum: support.Hardware 03 July 2018, 11:18
Replies: 6
Views: 264
Posted By Jope
Or just swap the tick jumper to VSYNC.

Or just swap the tick jumper to VSYNC.
Forum: support.Hardware 02 July 2018, 21:05
Replies: 13
Views: 401
Posted By Jope
After you reflashed, did you apply any (default)...

After you reflashed, did you apply any (default) settings to it?
Forum: support.Hardware 02 July 2018, 20:47
Replies: 13
Views: 401
Posted By Jope
http://wiki.icomp.de/wiki/Indivision_AGA_MK2...

http://wiki.icomp.de/wiki/Indivision_AGA_MK2 please find the tools + cores here.
Forum: News 02 July 2018, 06:42
Replies: 888
Views: 99,191
Posted By Jope
When talking about drives connected to the Amiga,...

When talking about drives connected to the Amiga, you should look at the Amiga disk pinout.. So there pin34 is ready, pin2 is diskchange.
...
Forum: Amiga scene 29 June 2018, 06:46
Replies: 37
Views: 1,627
Posted By Jope
The only DMA IDE for the Amiga is the Masoboshi...

The only DMA IDE for the Amiga is the Masoboshi 702.
Forum: Amiga scene 28 June 2018, 20:26
Replies: 37
Views: 1,627
Posted By Jope
Probably the problem was: no m68k / zorro...

Probably the problem was: no m68k / zorro compatible DMA IDE controllers available during the early 90s and designing an ASIC was too expensive for the volumes that would be sold reasonably, SCSI was...
Forum: support.Hardware 28 June 2018, 18:21
Replies: 13
Views: 437
Posted By Jope
CGX is my personal choice, I always found it a...

CGX is my personal choice, I always found it a bit more user friendly than P96 + draggable RTG screens, can't say no to that. ;-)

You should install all the updates, especially 3.9 was somehow...
Forum: support.Hardware 28 June 2018, 11:33
Replies: 17
Views: 774
Posted By Jope
Cracks in the laquer -> air gets in and starts...

Cracks in the laquer -> air gets in and starts corroding the traces.
Forum: support.Hardware 28 June 2018, 11:32
Replies: 13
Views: 279
Posted By Jope
How are you replacing your ROMs? Is your A3000...

How are you replacing your ROMs? Is your A3000 equipped with a ROM tower?
Forum: support.Hardware 28 June 2018, 11:31
Replies: 20
Views: 488
Posted By Jope
Hours? Should be done in a matter of minutes....

Hours? Should be done in a matter of minutes. Perhaps yours are indeed worn too low or something. The idea is to wipe only enough that they are dull again. In my experience that's like 10-20 wipes...
Forum: support.Hardware 28 June 2018, 06:15
Replies: 8
Views: 333
Posted By Jope
Looking at the photos you attached, that system...

Looking at the photos you attached, that system was booted from one of the WB 1.4 floppies floating around the internet to get the last screenshot.

The early startup and hdtoolbox screenshots...
Forum: support.Hardware 27 June 2018, 13:35
Replies: 20
Views: 488
Posted By Jope
I'd just keep wiping with the paper. :-) If the...

I'd just keep wiping with the paper. :-) If the rubbers aren't split/cracked, you can rejuvenate them.

I would not use graphite.
Forum: support.Hardware 27 June 2018, 09:06
Replies: 20
Views: 488
Posted By Jope
You need to look under the keyboard to be sure....

You need to look under the keyboard to be sure. Look for the letters KPQ in the model number sticker under the keyboard.

Handy ebay search: https://www.ebay.de/sch/i.html?_nkw=mitsumi+kpq

I...
Forum: support.Hardware 26 June 2018, 14:21
Replies: 9
Views: 576
Posted By Jope
The important question still remains: why doesn't...

The important question still remains: why doesn't loadmodule work with this aca1221ec?
Forum: support.Hardware 26 June 2018, 14:04
Replies: 47
Views: 1,261
Posted By Jope
"If you have to ask.." ;-) It's not that...

"If you have to ask.." ;-)

It's not that difficult to desolder with a hot air station. If you don't have hot air, I recommend just cutting the old chips out and soldering in sockets for the new...
Forum: Amiga scene 26 June 2018, 09:27
Replies: 37
Views: 1,627
Posted By Jope
They were embarrassed with it being PIO IDE.. Had...

They were embarrassed with it being PIO IDE.. Had it been DMA IDE, it wouldn't have been such an embarrassment.
Forum: support.Hardware 26 June 2018, 09:22
Replies: 7
Views: 208
Posted By Jope
Agreed, it's a fun project if you have time to...

Agreed, it's a fun project if you have time to waste, but an ethernet solution is much more convenient.
Forum: support.Hardware 26 June 2018, 09:21
Replies: 20
Views: 488
Posted By Jope
If your only problem is shiny rubber contacts,...

If your only problem is shiny rubber contacts, you can take a piece of paper from your printer and use that to wipe at the rubbers until they are no longer shiny.

Clean any paper dust from the...
Forum: support.Hardware 26 June 2018, 09:16
Replies: 8
Views: 333
Posted By Jope
Ok, I found it a bit difficult to understand your...

Ok, I found it a bit difficult to understand your message.

If you don't quit out into 1.4 from the kickstart selection menu, it works correctly?

A 2.04 system is not expected to boot properly...
Showing results 1 to 40 of 6680

 
Forum Jump

All times are GMT +2. The time now is 06:48.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.
Page generated in 0.41510 seconds with 10 queries