English Amiga Board


Go Back   English Amiga Board > Search Forums
Reload this Page Search Results
Register Amiga FAQ Rules & Help Members List  /  Moderators List Today's Posts Mark Forums Read

Showing results 1 to 12 of 12
Search took 0.33 seconds. Search: Posts Made By: silverfox0786
Forum: Hardware mods 11 February 2018, 04:14
Replies: 4,059
Views: 754,857
Posted By silverfox0786
Ah right I thought you was traveling Glasgow to...

Ah right I thought you was traveling Glasgow to London. Lovely Arizona. But how come your not flying straight to Glasgow or are you planning to catch a connect from London.


Sent from my iPhone...
Forum: Hardware mods 11 February 2018, 04:08
Replies: 4,059
Views: 754,857
Posted By silverfox0786
Ah good idea I’ll get the scope prepped at some...

Ah good idea I’ll get the scope prepped at some point and check it.

You prob would have been quicker driving from Glasgow to London at this rate.

Hopefully I can figure this out otherwise I...
Forum: Hardware mods 11 February 2018, 03:58
Replies: 4,059
Views: 754,857
Posted By silverfox0786
https://i.imgur.com/QYwtpwF.jpg

https://i.imgur.com/QYwtpwF.jpg
Forum: Hardware mods 11 February 2018, 03:57
Replies: 4,059
Views: 754,857
Posted By silverfox0786
EDO chips ...

EDO chips
https://www.mouser.co.uk/ProductDetail/870-IS41C16100C50TLI

i matched the orientation correctly as well

tried the other chips 00600000-00A00000 and still same results

and cant...
Forum: Hardware mods 11 February 2018, 03:40
Replies: 4,059
Views: 754,857
Posted By silverfox0786
exactly the same results as image above ...

exactly the same results as image above

dram is pretty sensative have these ISSI chips been known to die during soldering as i cant think of any other reason

nevr have issues in the past when...
Forum: Hardware mods 11 February 2018, 03:23
Replies: 4,059
Views: 754,857
Posted By silverfox0786
at the first boot i select option 9 and it...

at the first boot i select option 9 and it alocates ZII to 00200000 to 00A00000

i then selct option 3 test detected fastmem and i get no RAM found

if i go back to option 9 to autoconfig it...
Forum: Hardware mods 11 February 2018, 03:09
Replies: 4,059
Views: 754,857
Posted By silverfox0786
1: could be a possibility still new to diagrom ...

1: could be a possibility still new to diagrom
2: I've doubled checked all connections and cant see any obvious unsolddered or weak pads
3: Re programmed and verified both CPLDs and still showing...
Forum: Hardware mods 11 February 2018, 02:45
Replies: 4,059
Views: 754,857
Posted By silverfox0786
i dont think that was very definative I...

i dont think that was very definative

I assume none of teh 8MB ISSI chips have been detected

very confused by that as they are brand new from Mouser


https://i.imgur.com/gvNJgTb.jpg
Forum: Hardware mods 11 February 2018, 01:19
Replies: 4,059
Views: 754,857
Posted By silverfox0786
does this make any sense? im new to all this...

does this make any sense?

im new to all this

how do i autoconfig the ram and do other tests

i did also go through every single pin of evry ram and cpld and no shorts whihc i suspected...
Forum: Hardware mods 10 February 2018, 23:46
Replies: 4,059
Views: 754,857
Posted By silverfox0786
the error is present in either CLK jumper...

the error is present in either CLK jumper possition.

I havent tred IDE just yet

i have always wondered how to wire up the Serial so i can use DIAGrom via putty, programming an EPROM is no...
Forum: Hardware mods 10 February 2018, 23:14
Replies: 4,059
Views: 754,857
Posted By silverfox0786
hi guys could do with some help please ...

hi guys could do with some help please

finished soldering my TF328 CD32 and programmed it up. used a microscope to check my solder work as well

after plugging it in i seem to be getting an...
Forum: MarketPlace 30 November 2017, 22:15
Replies: 46
Views: 11,400
Posted By silverfox0786
Id like to buy one please. can you pm me

Id like to buy one please. can you pm me
Showing results 1 to 12 of 12

 
Forum Jump

All times are GMT +2. The time now is 17:32.

Top

Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2024, vBulletin Solutions Inc.
Page generated in 0.54923 seconds with 10 queries