English Amiga Board


Go Back   English Amiga Board > Search Forums

Showing results 1 to 40 of 10000
Search took 1.75 seconds.
Search: Posts Made By: Toni Wilen
Forum: support.Hardware Yesterday, 22:22
Replies: 3
Views: 97
Posted By Toni Wilen
If you remove ACA1233n, does ACA500plus...

If you remove ACA1233n, does ACA500plus autoconfig screen (and showconfig/sysinfo) list same autoconfig boards (except missing ACA1233n RAM at $40000000)?

A1200 accelerator + ACA500plus can have...
Forum: project.WHDLoad Yesterday, 18:56
Replies: 36
Views: 1,342
Posted By Toni Wilen
There are also 2 different audio hack options: ...

There are also 2 different audio hack options:

- KS audio.device workaround, it sets period to very low value (4 or so) and assumes audio state goes to zero quickly enough. AFAIK only JIT can...
Forum: Coders. Asm / Hardware 17 February 2020, 19:37
Replies: 16
Views: 562
Posted By Toni Wilen
68000/010 always has at least next word...

68000/010 always has at least next word prefetched. 68020+ have longer pipeline and have at least 2 following words prefetched.

Reason for requiring long word is most likely misunderstanding of...
Forum: Coders. Asm / Hardware 17 February 2020, 12:16
Replies: 16
Views: 562
Posted By Toni Wilen
It is wrong. All CPUs prefetch at least following...

It is wrong. All CPUs prefetch at least following opcode word, long alignment is not required.
Forum: support.WinUAE 16 February 2020, 21:31
Replies: 3
Views: 303
Posted By Toni Wilen
Commodore bridgeboards are emulated because they...

Commodore bridgeboards are emulated because they are almost fully documented in register level, both Amiga and PC visible sides.

All other PC bridgeboards don't have any technical documentation.
Forum: Coders. Asm / Hardware 16 February 2020, 16:06
Replies: 16
Views: 562
Posted By Toni Wilen
68020+ always loads opcodes using long word...

68020+ always loads opcodes using long word accesses (if memory has 32-bit bus, if not, it uses bus sizing hardware to do multiple reads). If address is not long word aligned, long from address - 2...
Forum: support.WinUAE 16 February 2020, 13:08
Replies: 2
Views: 210
Posted By Toni Wilen
D3D11 has been GUI option at least for 2 years. ...

D3D11 has been GUI option at least for 2 years.

Main difference between D3D11 and D3D9: D3D11 is Windows built-in in later Windows versions, no need for ancient D3D9 redistributable.

D3D11...
Forum: project.WHDLoad 16 February 2020, 11:05
Replies: 36
Views: 1,342
Posted By Toni Wilen
You could try latest winuae.7z, it logs first 100...

You could try latest winuae.7z, it logs first 100 possible audio dma wait issues (restart needed to reset it) and all automatic too fast cpu hacks can be disabled with chipset_hacks=8 config file...
Forum: News 15 February 2020, 19:30
Replies: 54
Views: 7,548
Posted By Toni Wilen
I am not sure 68020+ support is still working...

I am not sure 68020+ support is still working (test and report if interested enough :)). I'll add full 68010 support next. Then it is time for 68020+ again.

CHK2 probably is/was wrong because...
Forum: News 15 February 2020, 17:17
Replies: 54
Views: 7,548
Posted By Toni Wilen
68000 test is now complete and re-verified with...

68000 test is now complete and re-verified with real 68000.

Small test set that does not need extra hardware (no bus error test) is also uploaded. http://www.winuae.net/files/b/cputest_data.7z...
Forum: support.Other 15 February 2020, 10:27
Replies: 4
Views: 183
Posted By Toni Wilen
Try clicking Misc panel GUI section "Set default"...

Try clicking Misc panel GUI section "Set default" button.

It should automatically be correct unless you also imported old registry or ini data. GUI scaling does not work the same between different...
Forum: support.WinUAE 15 February 2020, 10:10
Replies: 7
Views: 504
Posted By Toni Wilen
It sounds like something outside of WinUAE if it...

It sounds like something outside of WinUAE if it also goes out of sync in A500 configurations. Or you have huge buffer size. Reason can't be CPU speed, no one has that slow PCs today..

Check sound...
Forum: support.Other 15 February 2020, 10:05
Replies: 15
Views: 1,380
Posted By Toni Wilen
You can try this:...

You can try this: http://www.winuae.net/files/b/pfsdoctor_experimental.zip

Note that it is command line only. Try "CHECK" parameter first.
Forum: Coders. Asm / Hardware 13 February 2020, 10:08
Replies: 9
Views: 479
Posted By Toni Wilen
Yeah, DDFSTRT is "unaligned" if BPLCON1 seems to...

Yeah, DDFSTRT is "unaligned" if BPLCON1 seems to work unexpectedly (display jumps to left when you increase BPLCON1 value). You don't need "aligned" DDFSTRT, simply add opposite offset to value you...
Forum: News 11 February 2020, 18:41
Replies: 398
Views: 63,412
Posted By Toni Wilen
Hopefully this can be reliably duplicated by some...

Hopefully this can be reliably duplicated by some kind of test program that creates lots of files, waits a bit, then attempts to delete them. Without test case it is too annoying to debug..
Forum: support.Hardware 11 February 2020, 18:37
Replies: 89
Views: 2,960
Posted By Toni Wilen
I'd only call PC PSU modern if it uses DC-DC...

I'd only call PC PSU modern if it uses DC-DC internally (has big 12v output and 3.3v and 5v is generated by DC-DC converters from 12v) and does not have minimum load requirements ("Haswell ready",...
Forum: support.Hardware 11 February 2020, 18:32
Replies: 8
Views: 381
Posted By Toni Wilen
It still is guaranteed to not have anything to do...

It still is guaranteed to not have anything to do with size. Perhaps there is some other compatibility problem but it isn't size related (Someone probably assumed something, back in the day, when...
Forum: support.WinUAE 11 February 2020, 18:05
Replies: 23
Views: 1,052
Posted By Toni Wilen
Standard A500 config (even without cycle-exact)...

Standard A500 config (even without cycle-exact) seems to work fine.
Forum: support.WinUAE 10 February 2020, 12:04
Replies: 1
Views: 720
Posted By Toni Wilen
You are using 60Hz refresh rate, vsync matches...

You are using 60Hz refresh rate, vsync matches refresh rate and also matches sound (without it sound would glitch all the time)

I am sure it has nothing to do with sound mode.
Forum: support.Other 09 February 2020, 20:25
Replies: 15
Views: 1,380
Posted By Toni Wilen
PFS3AIO 19.0 or 19.1 fixed original PFS3 bug that...

PFS3AIO 19.0 or 19.1 fixed original PFS3 bug that can cause block id errors if drive is "large" (~>5G). It usually can only happen when lots of (small) files are created very quickly (for example...
Forum: support.WinUAE 09 February 2020, 12:50
Replies: 35
Views: 1,615
Posted By Toni Wilen
Ok, it will be logged but only first 100 or so...

Ok, it will be logged but only first 100 or so log messages because this could cause huge log flood with bad players in fastest possible mode.

This is quite special hack because it is so common...
Forum: support.WinUAE 09 February 2020, 10:06
Replies: 35
Views: 1,615
Posted By Toni Wilen
Thanks, now it is more clear. "lbC004EB2: useless...

Thanks, now it is more clear. "lbC004EB2: useless move.w d5,$96(a3)" detects too short DMA wait hack because it looks like missing DMA wait (switch off DMA, [too small delay would have been here...
Forum: support.WinUAE 08 February 2020, 15:18
Replies: 35
Views: 1,615
Posted By Toni Wilen
I finally checked this quickly bit but I am not...

I finally checked this quickly bit but I am not really sure how it is supposed to work, code makes no sense, most likely because coder didn't understand how audio interrupts work.. You can't simply...
Forum: support.WinUAE 08 February 2020, 14:28
Replies: 7
Views: 388
Posted By Toni Wilen
What did say "test complete"? At least not...

What did say "test complete"? At least not WinUAE.

Press Test button, then press F1-F10 one by one and verify that highlighted Input target lists matching F-key.

I am still quite sure that it...
Forum: support.WinUAE 08 February 2020, 12:31
Replies: 1
Views: 275
Posted By Toni Wilen
I don't know (as usual, neither Cybergraphics nor...

I don't know (as usual, neither Cybergraphics nor Picasso96 sources are available)

You can try testing if same happens when using native emulated graphics board (for example Picasso II or IV) and...
Forum: Coders. Asm / Hardware 07 February 2020, 20:55
Replies: 22
Views: 1,536
Posted By Toni Wilen
Few days ago I was doing unrelated interrupt line...

Few days ago I was doing unrelated interrupt line to IPL line change timing tests and noticed there is 2 CCK delay between first AUDxDAT Agnus DMA write and before Paula IPL line changes state.

I...
Forum: support.WinUAE 07 February 2020, 20:36
Replies: 10
Views: 739
Posted By Toni Wilen
It looks like Windows still wants to take desktop...

It looks like Windows still wants to take desktop screenshot even when WinUAE has focus. I am quite sure it didn't happen previously (previously = could be many years ago, possibly when Windows 10...
Forum: support.WinUAE 05 February 2020, 20:41
Replies: 2
Views: 246
Posted By Toni Wilen
There is no simple adjustment (at least not yet)...

There is no simple adjustment (at least not yet) but filter mode "overscan blanking" does something similar.

Make sure aspect ratio matches your monitor (or is automatic) to keep correct aspect...
Forum: support.WinUAE 05 February 2020, 20:23
Replies: 174
Views: 31,097
Posted By Toni Wilen
OS 4.1 FE has only update #1. Other updates are...

OS 4.1 FE has only update #1. Other updates are for older OS 4.1 version which does not support Z3 RAM as system RAM.
Forum: support.WinUAE 04 February 2020, 19:07
Replies: 6
Views: 484
Posted By Toni Wilen
It is old realtek, it probably sucks in later...

It is old realtek, it probably sucks in later Windows versions without proper driver. Try some generic realtek driver without mainboard specific stuff.
Forum: support.WinUAE 04 February 2020, 18:51
Replies: 6
Views: 803
Posted By Toni Wilen
I still can't duplicate it and you didn't include...

I still can't duplicate it and you didn't include log either but I'll still add a possible workaround: when exiting debugger, if next key event is release, it will be ignored.
Forum: support.Hardware 03 February 2020, 18:53
Replies: 8
Views: 192
Posted By Toni Wilen
You really need floppy drive or some other...

You really need floppy drive or some other working media to confirm if drive is detected (scsi.device appears in device list and hdtoolbox detects the drive) or if there are some other problems.
...
Forum: support.Hardware 03 February 2020, 18:24
Replies: 8
Views: 192
Posted By Toni Wilen
No. It still isn't true. I just tested (yet...

No. It still isn't true.

I just tested (yet again). Real A600 + official 37.300 ROM + 2G partition (CF in CF adapter). It boots normally.
(And there is no technical reasons whatsoever that would...
Forum: support.WinUAE 02 February 2020, 18:18
Replies: 4
Views: 376
Posted By Toni Wilen
This is not SCSI controller that just works...

This is not SCSI controller that just works automatically.

Drive/HDF _physical_ geometry must exactly match what you selected in partitioning program.

(EDIT: there was some thread how to...
Forum: support.WinUAE 02 February 2020, 18:07
Replies: 6
Views: 484
Posted By Toni Wilen
WASAPI has been there for ages already. No need...

WASAPI has been there for ages already. No need for XAudio.
Forum: Nostalgia & memories 01 February 2020, 23:27
Replies: 2,467
Views: 371,928
Posted By Toni Wilen
PFS3AIO has experimental variant with >4G file...

PFS3AIO has experimental variant with >4G file size support (official pfs3aio has it disabled) and I think normal version will support up to 4G-1 files. UAE directory filesystem also supports max...
Forum: support.WinUAE 01 February 2020, 23:18
Replies: 3
Views: 450
Posted By Toni Wilen
Yeah, it should have at least almost correct...

Yeah, it should have at least almost correct speed.

CD32 also uses 1x speed as a backwards compatibility feature if inserted CD is for CDTV.
Forum: support.WinUAE 01 February 2020, 23:12
Replies: 1
Views: 311
Posted By Toni Wilen
Perhaps your config file is located in read-only...

Perhaps your config file is located in read-only path? (like in program files. which is not meant for user files)
Forum: Coders. Asm / Hardware 01 February 2020, 23:11
Replies: 30
Views: 1,468
Posted By Toni Wilen
I didn't touch any floppy CIA registers (so no...

I didn't touch any floppy CIA registers (so no floppy selected, no motor started etc..)

I only switched on and off WORDSYNC bit and removed internal drive.
Forum: Coders. Asm / Hardware 01 February 2020, 21:41
Replies: 30
Views: 1,468
Posted By Toni Wilen
Few bits of random data was injected to bit...

Few bits of random data was injected to bit buffer to simulate motor start delays/step to other track/PLL not yet in sync etc.. And it was injected even when no floppy drive was selected.



No.
Showing results 1 to 40 of 10000

 
Forum Jump

All times are GMT +2. The time now is 10:01.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2020, vBulletin Solutions Inc.
Page generated in 1.18126 seconds with 10 queries