English Amiga Board


Go Back   English Amiga Board > Search Forums

Showing results 1 to 40 of 6869
Search took 0.61 seconds.
Search: Posts Made By: Jope
Forum: support.Hardware 09 November 2018, 16:31
Replies: 8
Views: 172
Posted By Jope
It all depends on your motherboard revision.....

It all depends on your motherboard revision.. Perhaps check that first.
Forum: News 09 November 2018, 15:33
Replies: 244
Views: 12,936
Posted By Jope
They're all printed on the back of the A500...

They're all printed on the back of the A500 manual..

http://www.bombjack.org/amiga/amiga-commodore/Amiga_500_Introduction.pdf page 242-> Most of them are accurate :-) At least the s keymap is very...
Forum: support.Hardware 09 November 2018, 15:25
Replies: 8
Views: 172
Posted By Jope
The two largest (or only the largest?) maps of...

The two largest (or only the largest?) maps of Turbo RAKETTI 1 also requires 1MB of Chip. :-)
Forum: support.Hardware 09 November 2018, 13:43
Replies: 8
Views: 172
Posted By Jope
Benefit: more screens open at the same time,...

Benefit: more screens open at the same time, larger music modules possible in protracker.. Basically you can do more with audio/gfx.

If you mainly care about playing games, 512/512 is usually...
Forum: support.Hardware 09 November 2018, 13:27
Replies: 8
Views: 172
Posted By Jope
Almost any A500 can be upgraded to 1MB of Chip...

Almost any A500 can be upgraded to 1MB of Chip RAM by swapping the Agnus and reconfiguring a few jumpers.

The rev5 is moderately easy to do and the rev6 is the easiest.

Usually people make...
Forum: support.Hardware 08 November 2018, 21:29
Replies: 27
Views: 684
Posted By Jope
It depends a lot on the adf writing tool whether...

It depends a lot on the adf writing tool whether the disk must be formatted. Some require preformatted disks.
Forum: support.Hardware 08 November 2018, 17:51
Replies: 8
Views: 249
Posted By Jope
Are the joystick port pins all straight?

Are the joystick port pins all straight?
Forum: support.Hardware 08 November 2018, 07:45
Replies: 7
Views: 253
Posted By Jope
It's nice for a RAM disk, but the machine does...

It's nice for a RAM disk, but the machine does really slow down once you hit the Zorrro3 ram board. It's noticeable even with my otherwise stock 25MHz A3000.
Forum: Hardware mods 08 November 2018, 07:42
Replies: 4,059
Views: 352,893
Posted By Jope
It was his decision and he did it himself. I...

It was his decision and he did it himself.

I guess I'll lock this thread for now, we'll reopen it if he decides to come back. Any meta discussion around him leaving should happen in another part...
Forum: support.Hardware 07 November 2018, 17:47
Replies: 7
Views: 253
Posted By Jope
Slower.

Slower.
Forum: support.Hardware 07 November 2018, 15:47
Replies: 5
Views: 167
Posted By Jope
That looks like a drive that was originally...

That looks like a drive that was originally shipped with an A600 or A1200.
Forum: Nostalgia & memories 07 November 2018, 09:02
Replies: 15
Views: 742
Posted By Jope
All the best screen hacks broke with OS2.x :-) ...

All the best screen hacks broke with OS2.x :-)

I always used to have the four sprite MTV logo in the corner of my screen for some reason. :-D
Forum: support.Hardware 06 November 2018, 13:25
Replies: 2
Views: 124
Posted By Jope
Any Mitsumi made A500 keyboard should have the...

Any Mitsumi made A500 keyboard should have the key for you. Just get one that has the same width shift key..
Forum: News 02 November 2018, 09:11
Replies: 587
Views: 55,637
Posted By Jope
What he said. I do have some mouse button...

What he said.

I do have some mouse button checks in my s-s too in case I want some other things.
Forum: support.Hardware 01 November 2018, 15:56
Replies: 3
Views: 541
Posted By Jope
Check the back of the a500 user's guide. ...

Check the back of the a500 user's guide.

http://www.bombjack.org/amiga/amiga-commodore/Amiga_500_Introduction.pdf page 263

This is at least closer to rev3 than anything else, but I suspect it...
Forum: News 31 October 2018, 22:47
Replies: 587
Views: 55,637
Posted By Jope
I use 1.8 too, it's loaded into my kickflash....

I use 1.8 too, it's loaded into my kickflash. Just boot with no startup-sequence and it will annoy you with the requester.
Forum: News 31 October 2018, 21:51
Replies: 587
Views: 55,637
Posted By Jope
Out of interest, what is the latest romable...

Out of interest, what is the latest romable KingCON these days + does it pop up the Please insert ENV requester when booting without startup-sequence?
Forum: support.Hardware 31 October 2018, 11:16
Replies: 8
Views: 291
Posted By Jope
If it's a warez disk, an adf + jpg of it is much...

If it's a warez disk, an adf + jpg of it is much easier to store reliably, though. Make a few copies onto separate drives, take one to work, leave one on a shelf at home..
Forum: MarketPlace 31 October 2018, 09:23
Replies: 37
Views: 1,988
Posted By Jope
Then adjust the parameters. Use fewer revolutions...

Then adjust the parameters. Use fewer revolutions per track.
Forum: support.Hardware 30 October 2018, 19:26
Replies: 8
Views: 291
Posted By Jope
No need to worry about static electricity.

No need to worry about static electricity.
Forum: support.WinUAE 30 October 2018, 15:41
Replies: 4
Views: 350
Posted By Jope
And if it's an Amiga partition inside a GPT or...

And if it's an Amiga partition inside a GPT or MBR disk, then:

- if you made an RDB inside the GPT partition, you must losetup -fP the partition to get the kernel to read the RDB partitions from...
Forum: support.WinUAE 30 October 2018, 14:10
Replies: 4
Views: 350
Posted By Jope
You should definitely use GPT or MBR partitions...

You should definitely use GPT or MBR partitions on your hard disk, this is a PC where it is connected, so RDB partitions would not be a good match.

You said you're using Linux, which means you...
Forum: support.Hardware 30 October 2018, 13:52
Replies: 4
Views: 166
Posted By Jope
A 40 pin IDE cable doesn't ruin anything if it's...

A 40 pin IDE cable doesn't ruin anything if it's connected upside down. In any case, when looking towards the pins with the notch in the connector shroud pointing upwards, pin 1 (with the stripe on...
Forum: News 30 October 2018, 09:38
Replies: 12
Views: 833
Posted By Jope
Thanks for all the work you've put into these. :-)

Thanks for all the work you've put into these. :-)
Forum: support.Hardware 30 October 2018, 09:15
Replies: 6
Views: 366
Posted By Jope
No problem. This is a kickstart 1.x feature. The...

No problem. This is a kickstart 1.x feature. The ROM keymap is the A1000 keymap (the A1k keyboard is actually missing those keys) for backward compatibility.. I guess some early application wanted...
Forum: request.Demos 29 October 2018, 21:46
Replies: 38
Views: 9,907
Posted By Jope
Thank you!

Thank you!
Forum: request.Demos 29 October 2018, 21:26
Replies: 38
Views: 9,907
Posted By Jope
Ok.. The lha version I have on my Amiga doesn't...

Ok.. The lha version I have on my Amiga doesn't extract or list them, neither does the one I got from macports, nor the one I have on my linux machine. Neither does WinRAR on my Win PC.

I ran...
Forum: support.Apps 29 October 2018, 21:13
Replies: 5
Views: 439
Posted By Jope
I always found it a bit strange that they removed...

I always found it a bit strange that they removed setmap completely. Setkeyboard only sets the keymap for the console window it is run in, but doesn't affect the system keymap.

You basically need...
Forum: support.Apps 29 October 2018, 21:08
Replies: 6
Views: 325
Posted By Jope
The amigaos install disks have an unstick tool as...

The amigaos install disks have an unstick tool as well from 2.1 onwards, called IconPos.

You can scriptify it:
list #?.info FILES LFORMAT "IconPos >NIL: *"%p%n*" -1 -1\" >ram:unstick
execute...
Forum: request.Demos 29 October 2018, 20:08
Replies: 38
Views: 9,907
Posted By Jope
The demoreels are missing from the LHA, does...

The demoreels are missing from the LHA, does anyone have the zip? :-)
Forum: support.OtherUAE 29 October 2018, 14:25
Replies: 3
Views: 375
Posted By Jope
The installation instructions are quite difficult...

The installation instructions are quite difficult to follow, if you don't do a bit of investigation first. It depends a lot on what kickstart you booted into when doing the installation. If you did...
Forum: support.Hardware 29 October 2018, 12:54
Replies: 6
Views: 366
Posted By Jope
Boot a workbench 1.3 floppy all the way, try the...

Boot a workbench 1.3 floppy all the way, try the keys then.
Forum: support.OtherUAE 28 October 2018, 20:44
Replies: 3
Views: 375
Posted By Jope
How about you use c:loadmodule...

How about you use c:loadmodule libs:intuition.library instead of romupdate.
Forum: support.WinUAE 28 October 2018, 10:56
Replies: 12
Views: 536
Posted By Jope
Yep, this is some kind of rich word processing...

Yep, this is some kind of rich word processing file and you want just the text without any special word processor specific data included.

If you want a more feature rich editor than ed, then...
Forum: support.WinUAE 27 October 2018, 11:38
Replies: 12
Views: 536
Posted By Jope
If you get an @ glyph, it should be an @ glyph....

If you get an @ glyph, it should be an @ glyph. There's only one in latin-1.

You can type yourguide.guide opt h to see if there are other characters there that shouldn't be.

Are you sure your...
Forum: support.Hardware 27 October 2018, 09:13
Replies: 9
Views: 261
Posted By Jope
Keyboard reset will require an additional...

Keyboard reset will require an additional circuit, there are plans for this on Aminet.
Forum: support.Hardware 25 October 2018, 18:14
Replies: 3
Views: 207
Posted By Jope
I've yet to have a SID die because of heat. I've...

I've yet to have a SID die because of heat. I've killed a few with potential differences when hooking up audio cables, before I wised up. :-)

But yes, there are a few self destructing CSG/MOS...
Forum: support.Hardware 25 October 2018, 16:08
Replies: 3
Views: 207
Posted By Jope
I see you've been influenced by the C-64 retro...

I see you've been influenced by the C-64 retro scene's obsession with heatsinks.

In my opinion you don't have to add cooling to any of the Amiga's custom chips. Just leave the RF shield out and...
Forum: Nostalgia & memories 25 October 2018, 12:48
Replies: 25
Views: 1,718
Posted By Jope
I shouldn't have sold my A3000T. Or I should at...

I shouldn't have sold my A3000T. Or I should at least have taken the upgraded DMAC+RAMSEY out and reinstalled the old versions when I sold it. :-)
Forum: Hardware mods 24 October 2018, 17:51
Replies: 401
Views: 344,362
Posted By Jope
This one would have been better asked in a thread...

This one would have been better asked in a thread such as http://eab.abime.net/showthread.php?t=69214

But anyway, X-Copy does not multitask, nor does it go through the levels of abstraction that...
Showing results 1 to 40 of 6869

 
Forum Jump

All times are GMT +2. The time now is 20:10.


Powered by vBulletin® Version 3.8.11
Copyright ©2000 - 2018, vBulletin Solutions Inc.
Page generated in 0.43936 seconds with 10 queries